¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Re: QMX receiver went deaf
Ludwig, Replacing ic402 and ic403 has corrected the issue.? The receiver is no longer deaf and passed all hardware tests.? Thank you for the help.? The basic trouble shooting you have written
By Ryan Wesolowski · #145735 ·
Re: U3S andLPF Relay Sw board
You just cycle through the menu hitting the <Menu> button without hitting the <Edit> button will show you each setting in order. There are 2 possibilities: FRAME TxS => TX windows to show If you
By Rob Giuliano · #145734 ·
Re: QMX+ printed assembly manuals
I printed it in black and white only. When in doubt I checked the colour photos on screen, enlarging them if needed. 20 May 2025 Sal 15:17 tarihinde Richard Dyer via groups.io <rdyer39=
By ta2rx bekir · #145733 ·
Re: QMX+ printed assembly manuals
Me? Printed and 3-Ring Binder with tabs for assembly/testing and users manuals.
By Richard Dyer · #145732 ·
Re: QMX+ printed assembly manuals
I do not print the whole manual. I do print the parts list for a check off list to verify all the correct components are present before construction. Using that list in conjunction with the components
By Steve W6WU · #145731 ·
Re: Microphone pre-amp
Yannig, If You have issues reaching the limit for free shipping from Digikey(and mouser), I usually add some Fair-rite ferrites to the order as they tend to find use :-) I recommend this one for
By Jonas Sanamon · #145730 ·
Re: QMX SSB low output
The qrp guys microphone works very well. Sometimes I have to repeat my callsign several times and? e like echo is sometimes like x-ray ..lol. But ist works and I could make some SSB QSOs.
By [email protected] · #145729 ·
QMX+ microphone list?
I know¡­.. lots of postings on QMX+ microphones here. Does anybody have a single list of working good/cheap mics? Thanks de K2RMA
By Roy Ashkenaz · #145728 ·
Estimate for Release of version 1.2 of ABS solution for QMX+
I just/finally bought my QMX+ at Dayton FDIM. Is there an estimate for the upcoming r elease of version 1.2 of ABS solution for QMX+? ? ?Where can I find more details, ie pictures and documentation?
By Roy Ashkenaz · #145727 ·
QMX+ printed assembly manuals
Do most folks print their QMX+ assembly manuals or just use/read them online? While I do own a Brother inkjet, does anyone know of a cheap online service to print single copies? My local (good folks)
By Roy Ashkenaz · #145726 ·
Re: Microphone pre-amp
Yeah, thats fair enough. I keep forgetting to switch of the external preamp, although the battery drain in minimal. I have the QMX+ so i have plenty of room in the case to install the preamp inside. I
By Mehmet Dinch · #145725 ·
Re: #qmx #Firmware release 1_02_000 #qmx #firmware
Yes, I have version 1.0 and it is working FB on SSB. Mike Krieger [email protected]> wrote:
By Mike Krieger · #145724 ·
Re: Microphone pre-amp
Hi Mehmet, I am sure that it helps but I am trying to minimise the number of potential points of failure as I sometimes operate portable. Aborting an outing because I forgot to check the microphone
By Yannig - F4IUJ · #145723 ·
Re: #qmx #Firmware release 1_02_000 #qmx #firmware
Many Thanks Stan 73 Bernd Dl3BLA
By Bernd DL3BLA · #145722 ·
Re: Microphone pre-amp
Hi Yanning, If it helps, I use a MAX9814 Arduino mic amplifier module powered by two AA batteries. The module come with a mic capsule on board. I removed the mic capsule and wired it to my gaming
By Mehmet Dinch · #145721 ·
Re: U3S andLPF Relay Sw board
Hi guys, Is there a way to see what bands/frequencies i have stored in the U3S ? It may be that I am not saving my setup correctly, it appears I am only storing 1 band at a time, not all 6 ? Thanks.
By Steve Shuff <steveshuff64@...> · #145720 ·
Re: QMX+ LCD blank on new build
I would first make sure all is functioning correctly,? RX and TX, before trying the calibration.? ?That removes one variable if something needs attention.? ?The calibration is optional,? and
By Stan Dye · #145719 ·
Re: QMX+ LCD blank on new build
Excellent!? I'm glad you found & fixed it. Mon, May 19, 2025 at 12:37 PM, Lincoln Thormahlen wrote: When you made this change, if you just did it via the menu, not everything will work correctly.?
By Stan Dye · #145718 ·
Re: Microphone pre-amp
Thanks Ludwig, I didn't realise that the 3.3V was just for high impedance. You saved me 5€ ! 73, Yannig F4IUJ
By Yannig - F4IUJ · #145717 ·
Re: #qmx #Firmware release 1_02_000 #qmx #firmware
Yes, all versions of QMX and QMX+
By Stan Dye · #145716 ·