开云体育

Nikolas, This is a great idea! Thanks for developing it. A friend printed it for me and I use it all the time to protect my QMX or QCX in my backpack. I like that it can double as a tilt stand,

Don't forget that the SSB capability will also expand the digital capability of this wonder rig. -- 73, Dan - W2DLC

Jeff did a great job saving my QCX+ 40M radio after I messed up the T1 coil and how it was soldered in. I sent him the radio and he had it diagnosed and back to me in less than a week. Awesome

Robbie, doing this maybe you bend the PCB a bit and a cold solder joint loosed connection? As far as I can see, it's a rev. 1 board ( with two SMPS subboards). Connections between the SMPS boards and

Hudson, no switch on without the 5V SMPS board (see schematics page 1 and QMX QMX_plus Startup ( /g/QRPLabs/wiki/36878 ) section 2). It looks like an overload to Q108 and L101

I think Han's 'wizard' idea is great, I can turn off the CW functionality and just keep the digital/ssb modes. Perfect!!!

Perhaps small tabs at the corners, outside current shell, stop the slipping. -- 72 de N4REE, Bob Easton - QRP CW forever

Hi Joe You are correct ""... and how you are holding the key making contact with exposed metal...""" ?and/or touching feed line connectors The issue is rf current on the outside shield of coax feed

Not all, did not have a ssb QSO since 2006. Heck i did not even solder internal mic on my QMX?

I built a midband QMX a couple months ago; it worked fine for a solid handful of QSOs and many hours of use in code practice mode. I was in the process of testing a newly built manual antenna tuner.

Thanks Pierre I have corrected the manual issue with the mis-placed photo at page 75. 73 Hans G0UPL http://qrp-labs.com https://www.buymeacoffee.com/g0upl [email protected]> wrote:

Hello Tony Single band or multi-band, the problem is the same. There is not any additional issue making the Si5351A do the necessary phase modulation on different bands. So the problem does not get

As we all wait for Hans to come up with the complete software for SSB, I wondered if there is a problem making it work at all frequencies due to the way the Si5351 will create the necessary phase

I stop torturing myself and will follow Hans' advice in his post /g/QRPLabs/message/134665. A quick calculation shows me that a basket including a QCX+ 40M kit with enclosure, GPS,

I ?played in the CQ WW CONTEST and concluded that it can go two ways with QRP. Sometimes the other station will try to dig out a weak signal for points; sometimes nothing gets through other strong

Thanks to all for your answers. I did this search /g/QRPLabs/search?d=0&ev=0&p=Created%2C%2Cmultiband+qcx%2B%2C20%2C1%2C0%2C0&ct=1&startdate=&enddate= and can see that this subject

Hi Jim, Maybe the led is bad. ? Can you try powering on the QDX and turning it off before 5 seconds elapsed? ?Then turn it on and try connecting to your computer. 73 Evan AC9TU

I can't find the firmware tweak, but it was nothing major; just a command change or something. I am still getting no communication via USB. The chips all? have their power supplied properly. It's

I sent my QMX off to Jeff (W1NC) and he reported back the following: How lucky we are to have Jeff eagerly taking interest in something causing me frustration. The bad PCM1804 chip was suggested as a

Steve M <steven@...> wrote: Thanks for all the responses! Actually 8m is forbidden where I live (Poland, IARU 1), so I wouldn't use it anyway. My issue (and my thinking) is this. In