开云体育

Nail polish works great. -- Tisha, AA4HA

This is what I did with paint-pens. I colored the lengths of wire and let them really dry before using the drill chuck to make them in a bundle. It also looks really pretty when you get it installed

Hi Dave and John, All good now, everything is working. Run Program does transmit while connected to USB power / Console. I figured out the HP=1 setting before complaining the outputs were still in

Further tests show poor 80/60m performance and there is a significant voltage drop compared with the other LPF’s. I set the band to 6m and found 10.47V at the switching diodes and their respective

Glad it’s stable. I saw similar and went round the gain puzzle It drops off at highest and lowest frequencies It reduces with low supply voltage ( I was using 13.5 V) It reduces as output level

I use this method and this realy work. https://www.youtube.com/watch?v=a8ViWS61hsU&ab_channel=w2aew Tarmo K?lli ES4RTK 16.09.2024 20:45 Chris Raine W3PB kirjutas: -- This email has been checked

My 4SQRP seems to make my SWR on 20M worse.? I think I can get it less that 2:1, but I finally put the analyzer on my antenna clean (no tuner) and am about 1.2:1 so I figure that is okay. Bob, The

Try also: /dev/ttyACM0 /dev/ttyUSB0 /dev/ttyUSB1 Of course this only applies to Linux.

I saw this method used on a Youtube video. ? It looks to me as though the builder has created the mythical “3rd arm growing out of the middle of my chest” with this lashup. ?A vice holds a

on my windows unit I had to open device manager, unplug and re-plug with usb devices open so I could see which com port I was on. I then turn on the QMX with the usb cable in place and launch PuTTY.

THANK YOU Tarmo! I checked that diode for short to ground but I didn’t think to look for a solder bridge there because I didn’t solder it lol. I will go over that board with a fine tooth comb when

Just completed a QMX, replaced a SMD capacitor I killed with the wire cutters (despite 40 years designing and manufacturing Electronics kit!!!), applied power via a variable voltage, current limited

Changing the input/output cables made the change. Now the amp is stable, the only remaining issue I have that I measure around 20-21dB gain... Thanks for the help!

I am running my QMX up to 2:1 without any issues so far, generally stop tuning at 1.5:1. Don't feel the case warming up. Doing only CW at this SWR though. Peter HB9EBE

Adrian, some times ago there was a post from Hans ( /g/QRPLabs/message/127587?p=%2C%2C%2C20%2C0%2C0%2C0%3A%3Arecentpostdate%2Fsticky%2C%2CQSK%2C20%2C2%2C0%2C107821405 ) about a

I’m fairly confident in the repairs I made to the 5V SMPS and it seems to be working fine. To validate the LCD, I removed it to rule out any issues. No performance change noted. With a departure

We finished assembling the QMX+. ?When performing the ADC I/Q test we observe no I phase present on all bands(flat line). ?Q phase looks fine. ?Looking at the possible trouble shooting issues it

I also had the same problem and the fault was on the 3.3V SMPS board. The solder had been repaired, but it was short-circuited. I used a desoldering wick and now everything is fine. Tarmo K?lli

Mark, A quick search for "QDM 4m" produces /g/QRPLabs/message/110602 from the horses mouth Well, QDX is pretty much the same. 73 Alan G4ZFQ

Thanks, everyone. Honestly, if it had not been the end of a long day happily hyperfocused on all the tiny toroids, I probably would have figured this out for myself. My spouse also suggested