开云体育

Thanks :)? Maybe I'll customize it with a stencil of a old style ship or something in the end, we'll see!? Digikey parts should arrive tomorrow according to Fedex, in theory, so I'll hopefully know

the laptop is mounted into the lid of the case by using some short alu profiles ... so I have a all-in-one ... may you can try your own ideas

Hi, I like to show you my new /p setup with QMX low band: you see? the QMX with pocket transmatch, speaker and accu talentcell yb1203000-usb.... the key is a tiny paddle by n6ara... for charging the

Dbl.click 300 - no reaction, 500 - works after 3-5 attempts, 600 - switch RIT on immediately. It was not so before, 300 was OK. 73 Igor oh2jxa

Chris, I think it still comes back to volume level. I tried using my little amplified speaker and the clicks are gone - that is until you turn the volume up to really uncomfortable levels - then they

Chris, I tried your settings and there is no change. Unless... you turn the volume way down. Volume level is the only thing that seems to make a difference. Low volumes, I don't hear clicks. High

Greg,? I think I also trimmed most of the tab off so it wouldn't interfere with other components. -- 73, Dan - W2DLC

I have to admit that I was a bit mystified as to how I managed to get the sidetone working perfectly as I initially played a lot with the settings to no avail and then the problem just seemed to

Dan, Rowan and Ron, thanks for your help.? I think I am off and running. 73, Greg, KM5GT

Torsten, RF getting into the USB cable? Try different cables, put chokes on cables. Or stop common-mode signals on the feeder. Reconfigure antenna. 72 Alan G4ZFQ

It's an easy mod. You just move the 7805 over to the left one pin and solder the left most pin to the bottom of the diode. -- 73, Dan - W2DLC

Tnx all.? Not that I *plan* on shorting the 5VDC to ground, but replacing the regulator with a 78M05 is appealing.? Where will I find details on that fix?? Is it drop-in, or does it require some

*Hans* - It looks like we have a real problem for many (most?) of us! Perhaps it is a bigger issue than we all realised. I welcome your comments please, meanwhile, back in the desk drawer it goes as,

Hello there :) I built a QDX (PCB Rev 5 and firmware 1_10) for 20, 17, 15, 12, 11 and 10m (12 volts version) that works well (rx & tx) on 15m, but fails running on 10m. The QDX is connected to a

BTW Martin, I had a really good laugh at your Ship of Theseus reference. Clever! Let's hope that changing out that Stereo ADC will be the last of it. Looking forward to seeing your All OK

Got my QMX on Monday March 10th. Did 2 QSO's 20m. CQ'ing again on tuesday - no rx at all. Transmit is fine to me. 1 - board revision: Rev3 so Hans told me - got it assembled from QRP-Labs and do not

I think the thumps are coming from the AGC and you disabled it. increasing sidetone volume to 60 also somehow helps. Simon

I only just started to test my QMX with a paddle a few days ago.? Initially I experienced the severe sidetone clicks that have been reported with the latest and previous version of firmware.? I made

Hi Greg, I bought an unbuilt kit of the same vintage recently. It requires a capacitor on the power input to prevent potential damage from supply spiking. D33 cathode to 0V. 10uF tantalum or

Hello Emory, 12, 11, and 10 meters share the same low pass filter (LPF).? This would point to a problem there.? The most common is one of the toroid connections did not burn through the enamel.?