开云体育

Bryan, Looking at the QCX+ schematic JP11 is the point for one pole of the switch. depending on which way I try). JP12 is right I see JP5? I'd rather cut the connection between IC9A pin 1 and

I would prefer that it not be oversimplified to an 'only' three settings. That is one aspect of things I dislike the most about canned settings is that they end up being tuned to one person's

I hope I can get the attention of Hans through this group. I raised a ticket (No. 5122) over three months ago regarding a faulty Progrock2. I have not had any response to that ticket. I have updated

I believe this is "Works as Designed." (If I recall correctly...) 73, Paul -- AI7JR -- Paul -- AI7JR

Hi Timo, I would try a factory reset.? It may be that during transmission, the EEPROM was corrupted. What version of firmware are you running? 73 Evan AC9TU

Many thanks for the nice new Firmware with AGC and S-meter Hans! All good, but would it be possible to make the side tone "smoother" at end? (Sorry, don't know how to desrcibe it in one word) After

Hi Everyone, New problem om my QDX.? Keep in mind, my QDX has been trouble free for the past year. The RF sweep on 15m is suddenly down to -50db.? All the other bands are at -1 db (10,11,17 ), bar

TNX Alan I stand corrected with respect to WSPR in my post above I was typing "WSPR" but thinking "ft-8" My statments above are correct in order for an unmodified QCX to help decode ft-8 tnx agn

Target: QMX firmware 1_00_017 (second release) Bug: QMX display and control and serial console frees when using VOL encoder when QMX is in menu. Reproduction steps: entering menu on QMX, select any

Bryan, The first is exactly what I suggested. The other two are very similar but I do not know why the slight variations were made. 73 Alan G4ZFQ

Can anyone tell me if this is a bug....? If I leave on the QMX all night long with WSPR running, there comes a time when it stops transmitting RF even though the display still shows it transmitting

Im interested in receiving wspr on my qcx+. I searched the topic and found 3 different mods , so not sure of the best one for my needs. one method from Maxwell jumped r27 to between r53 and

John, The entire WSPR segment is only 200Hz wide. The decoder centre frequency is fixed at 1500Hz. The only easy way to decode is to send 1400-1600Hz to the decoder. The QCX filter centre of 700Hz

How to receive WSPR via an unmodified CW receiver I do not own the QCX Mini but do own several QXC 1) The many/many (several dozen or more) stations I see/hear (at the same time) on a true SSB (Not

Did you switch off the QMX or the power supply? Could you check the voltage from your power supply during a switch on and off using a oscilloscope and a resistor as a replacement of the QMX? Switch in

Thank you. I just blew out the votive candle I had lit since finishing my kit! -- 72/73 de Steve, K9NUD https://youtube.com/@learnhamradio

Yes agree. I'm listening to a strong contest station on 80m now but with heavy QSB and I had to change Recovery dB/S from 10 to 60. Like all these AGC settings here. 73 Durk PA3BYW Op zo 18 feb

Jim, I think over time as others experiment with the AGC settings there will be plenty of examples of settings that will fit into those categories.? As an owner of an Elecraft K3 and K4, both of

AGC is really nice addition! Been playing with the settings - here are my current ones: Thresh 9 Slope? 40 Noise? 10 Hang? ?30 Smooth 50 Recovery 40 Blocks? 4 S9? ? ? ? ?9 AGC? ?

Wow, superb, thanks Hans. 73 Simon G0FCU.