开云体育

Axel, these lyrics can be sung to the tune of "Livin' on a Prayer" by Bon Jovi. Enjoy. :-)

It looks like your pin spacing and via dimensions are wrong... I found the OSC5A2B02 on ebay showing pin 1-3 and 1-5 with 19.05mm spacing.. pins 0.8mm. https://www.ebay.com/itm/332389156868 Your

Tnx QSO, N3OIK.

I found this right after my last post. The LRS-350-12 has an even higher current capability. I suppose if you were to invest in a new supply, you'd just go for a 24V or 50V supply anyway, so I may

Took a quick look in the instruction manual and project page. Couldn't find anything on current draw. You could try throwing a fuse in line with the DC supply that's close to 2.89A and see the

band pass, not band add

Hasn’t the first part been reduced to 17 turns pushed tightly together or 19 turns spread out? ?I rewound mine with 19 turns spread out and I saw the filter results against someone that did 17

Hi Mike, here it is. this is my first try at the thing. Stay tuned for the 3d Layout... Giuseppe Marullo IW2JWW - JN45RQ PS: please *DO* check pin orientation, hope it is right but it is easy to

I get the error message unknown USB device cod 43 on my win 11 computer. Also tried on a win 10 computer but same error. Also tried on a win 8 laptop where I downloaded the recommended driver in the

All: A number of you have written me privately to ask what is covered in Al's and my Microcontroller Projects for Amateur Radio book. I went to the ARRL's web page for the book and you were right--it

As I play more on the air with the QMX, I'm enjoying it more and more. Multi bands is great in a rig this size. I have been keeping track of little bugs. I am mainly a CW guy so my observation will

Is this one? https://easyeda.com/components/CTI-OSC5A2B02-10Mhz-OCXO_ea1ce85e0ab7468eb8857e8e97ff70f8 Giuseppe Marullo IW2JWW - JN45RQ

That goes mean, better using only 11V to get not more than 3-4 Watts to protect the BS170 transistors. In this case two zener diodes make really sense. better to have trx with 3-4 Watts working than a

I'm trying to build a Kicad Device schematic symbol and PCB footpring for the CTI OSC5A2B02 vctcxo. and failing at the first fence. All tutorials are for very simple 2 pin devices with no useful

I use 5 QCX including QCX-mini for different bands. I use 4x Li-On 16V as batteries. I always tune the antenna with the ATU-100. I've never had a problem with the BS170 before. 73 Zdenek

The relevant voltage is NOT 12V. The RF voltage is over 40V. For 5W into 50 ohms the voltage is roughly 47 V p-p. If the SWR is greater than 1:1 the voltage goes up. The BS170 has a max voltage of

If I use a 50W amplifier for QCX series with a 13.8V power supply, knowing that the output power will be reduced to around 15 to 20W what will be the DC intensity? I ask this question in order to know

Cliff, I'm looking at version 1.00f of the manual, dated July 8. Is there a newer version that I am not aware of? This is the image I am referring to. It clearly shows two taps, not one, and a 29th

Fancy Schmancy cable....(Hi Hi) Not_So_Anonymous

WB2CBA, The Zener trick you mention has been around and written up by some others before. After I found out about it, I added 51 V 1 W Zeners to my QDX and incorporated them into my QMX. I have 3