开云体育

Fancy Schmancy cable....(Hi Hi) Not_So_Anonymous

WB2CBA, The Zener trick you mention has been around and written up by some others before. After I found out about it, I added 51 V 1 W Zeners to my QDX and incorporated them into my QMX. I have 3

Hello I assembled a QDX Low Band Version 5. It powers on but does not flash quickly to initialize correctly. LED comes on steady and stays on. I power off and quickly back on it goes to firmware mode.

Cable not included. Get a cable does data. Some only charge. It'll be obvious that it's data capable when it specs transfer speeds. Doesn't matter what speed you get. This

With the shipment of my QMX nearing I have a dumb question.? Is a USBC to USBA cable or adapter included with the kit or do I need to find one in my junkbox (doubt I have one) or buy one?? Is a C to

I of course don’t know from start to finish how firm all of the statements are but after having been in electronic for the best part of my working career, my guess failure was most likely due to a

I was thinking having read something about a 50W PA. If this is like I understood, the QCX will see no harm: it will be the PA that will...

Mark, As above, There is one section of 19 winds and another of 9 winds.? The photo in the assembly manual has one winding hidden beneath the arrow that says Jumper Wire. The 9 wind segment begins

PSKReporter.info says that QDX was just heard in European Russia by UB3PEP at -21 dB snr from a DX of 5138 miles. Not sure I believe this one. Ten milliwatts @ 5138 mi on 40m in the east cost USA late

Good catch Mark - I didn't notice the picture in the upper right. Yes ignore that extra turn. At least I did and end on the 28th turn plus a jumper to the finish hole. Actually I just de-soldered all

Thanks, I like Hans and his products but It is so frustrating, when you know the fault seems to be not in your own responsibility. I also got comments that zener diodes have no results of... yes

Hi Barb, thanks I will try to replace the 4 BS170 and the 74ACT . In addition I will order two zener Diodes. But it is not easy to get these Zener diodes . High costs of shipping. We know us from

Matt, A ham friend of mine operated his QDX without any antenna connected by mistake. I repaired my friend’s QDX which had damaged BS170s and IC5 74ACT08. After replacing those QDX worked

Experience is very contrary to that of most QDX users. Maybe when you calm down a bit you can send a somewhat more objective email and we can help you. Mike WM4B Sent: Saturday, July 15,

Matt, That's why I dumped QDX, however, had I known about the simple zener-fix, then I might have stayed.. GL with QMX - someone at least saw fit to add Zeners! 73

I?m very angry about the tx quality of the high bands QDX, Rev 5. my first QDX high bands (rev3) was killed after a few day working good. I decided to buy a new one assembled. After 4 Months waiting

Mark, Sounds like you are using the old manual. Download the updated one. It will have the correct information. Someone also posted this picture which shows it also. 73, Cliff, AE5ZA

If the failure mode is overvoltage it can occur during a single dit, actually micro- to milliseconds. 73, Don N2VGU

Hi Mark, There are 2 windings, the first 19 wnd and the 2nd 9 windings. 73's Jacques PA3EVZ Op 15 jul. 2023 19:02, om 19:02, Mark Volstad - AI4BJ <mvolstad@...> schreef:

I built my QMX more than a month ago, then put it aside while awaiting for a solution to the 20M low sensitivity problem. I'm now ready to make the changes to L401 as described in the latest version