开云体育

I started WSJT-X with my RS-HFIQ, just to see if it would happen again, but noticed most of the computer applications have changed. I have updated versions of OmniRig, HDSDR, and WSJT-X since I had

My symptoms were that it would not put the radio in TX. I don't remember if there was an issue with uploading the data to WSPRNET. -- Rob KB8RCO

If indeed it is still receiving but not uploading to WSPRNet I would be looking at WSJT/Internet for the culprit ? John KK4ITX ?Each mistake is a learning opportunity.?

Yes, my mug looks like it is "bleeding" but the look adds to the "Homebrew" look of the mug and the whole kit building ethos haha! RichKQ9L

I have had a similar problem with my HobbyPCB RS-HFIQ radio. The issue came down to something with the CAT control, but I never narrowed it down any further. I did suspect it having something to do

I wonder if others have problems with the WSJT-X software?? Occasionally, perhaps once every 2 or 3 days, it will crash, showing an error message saying something like "Failed in sub process 1" (I

Hello, Robert. Four rigs, two antennas, two switches. The 80 meters long end-fed wire may be used on all four rigs - one at a time and is tuned by the Icom AH-4 remote automatic antenna tuner with

Dishwasher tablets and the water temperature are the killers. The water is much hotter than handwashing water and this can soften some image transfers. Dishwasher tablets contain abrasive particles to

Hi all The coffee cup print does indeed seem to suffer some drift or QSB in some dishwashers. Some time ago, I updated the shop page to state "Please wash by hand (not dishwasher)." It's disappointing

Solid state final amplifiers need to be followed by a low pass filter to take care of harmonics. (Back in the days of tubes, most radios used a final with a tuned tank circuit that acted as a bandpass

Hi, and you use four antennas? Otherwise, how do you prevent the rigs from destroying each other? 73 de Robert OE7OER Von: [email protected] <[email protected]> Im Auftrag von n4qa at_hotmail.com

I've wondered what constraints there are to making a multi band QCX. The front end BPF toroid would be one.

I built a QRP Labs 50W power amplifier for QCX and am driving it with a QDX.? Powering the amp with 13.8V.? I don't have a good power meter, so I don't know the output but I definitely am getting

Dave. I like both the core i3 and core i5 models ok, They're down here in Studio B. I have a second i3 in the sun room with the Malachite Malahit receiver. All my PCs are several years old now. Newest

Kevin, my kit contained a little bag marked "20 Meters" or words to that effect, containing the appropriate toroid cores and wire for that band. That's what I used to wind those coils and it all

Yep, been there, done that! the logo on my cup QRP cup is suffering from a little multipath and QSB, but still "coffeeable" Hi Hi Cheers de Dave VE7AHT

How do you like the Inspirion 15? Dave K9SW

Hi Tony. Your results may vary from mine. I just measured 4 watts on my QCX Mini 20 at 12.0 volts and 2 watts at 10.0 volts. Ron

All: Anyone using the 9 volt Bioenno battery with the QCX Mini? I'm told the battery will maintain 10v under load and was wondering what kind of power the Mini would putout at that voltage. I suspect

In the attached photo are the FT-450D, Modified QCX-17, Modified QCX-80 and the brand new QDX ! PC on left is the Dell Inspiron i3 - on the right is the Dell Inspiron i5. You might recognize a few