开云体育

This means you have a strong short on your VCC (5V) supply.? Something has failed internally.? If you are lucky, it is just a component on the SMPS board.? Some potential shorts happen due to the

On Thu, Jan 9, 2025 at 10:02 AM, Len wrote: Most? know of that hike the AT go for minimum weight as basic supplies food, and, water, and shelter take precedence. SOTA, IOTA, you have to carry in

Holiday season and family time slowed things a bit but i was able to finish speaker enclosure to acomaccompanie the main case for my qmx+. Amplifier module is TDA2030 and speaker is from old Compaq

Hi John, all QRP Labs shipping has always been charged at - as close as I am able to estimate - actual cost. FedEx shipping for 1 gram is the same as for 500 grams. It goes in 0.5kg increments. Note

Do you have a DMM or other method of measuring the Voltage and Current from your battery? The voltage and current before you press power-on, while you are pressing it, and after you release it are

3x18650 cell pack. I use 3200mAH ones. homebuilt 40-10m doublet antenna fed with 300 ohm line something like the EMTECH ZM-2 QRP tuner

Now,? does one need 2 of the 6 band relays to be able to switch bpf and lpfs together? or can only one or the other be controlled in operation? -- regards, Bryan, N0LUF

Go to YouTube. Search on ham radio sota. Spend hours watching. Lots of good stuff Ed AB8DF

Should work fine Bryan.? I have been very impressed by the receive module.? I am currently using it with no front end filtering for receiving wspr and FT8 with no problems. I am using an auduino

Ian, Thanks.? I run several qrss receivers here, so I'm familiar with how it's done in basic terms. I was planning on letting the U3S do its TX thing and use the receiver into wsjt-x for wspr decode,

I'm in awe, we all owe Jeff W1NC big time. Without him to back up our debug efforts, buying a QMX would be much riskier Reading how he went about this is instructive. Here's some other debug notes

Firstly...apologies to all for such a newbie question, but I only just ordered a QMX and am just now learning CW :) I was hoping to put together a rig for POTA while doing AT section hikes and was

Thanks Karl--and others-- who replied...I will check the wiki. I have played around with a lot of the qrp labs stuff...its great quality and never an issue. Just a bad run of luck lately is all.

Good Point. I forgot about that. Can’t just put it in an envelope. John Sent: Thursday, January 9, 2025 11:28 AM To: [email protected] Subject: Re: [QRPLabs] New silicone enclosure

Hi Bryan, The U3S is a stand alone transmitter only in that it does not need a computer to generate the wspr signals.? However to receive and decode wspr signals you will need a separate receiver,

Hello, Hans, I am using the 50W QCX PA with my QMX+ quite successfully. It works fine. There are some things that I am strictly sticking with when using this combination. 1. I am using a +5V PTT so I

Hi Hans, No, I did not try the other settings. I have read over the descriptions of what they do, and not knowing the architecture, I can't relate the settings to the problem I am seeing. I'm an

To follow up on a post praising Jeff Moore's (W1NC) revival of my dead QMX+, I wanted to share, with his permission, part of Jeff's email to me detailing the steps he took to convert my electronic

I mean, Turkey to Georgia (state, not country) is pretty far. I don't think they do Forever Stamps over there...

QMX Manual G4EDG Ron Other K7VIQ KL7MJ W5NR WA3UQV W2DLC Threshold 8 4 7 7 8 4 7 12 8 Slope 80 50 95 60 80 80 60 80 65 Noise 10 0 5 5 10 10 5 10 9 Hang 80 2 50 30 80 30 30 80 55 Smooth 50 0 99 50 50