开云体育

Wayne,

Based on the TX working with PuTTY, there is most likely a configuration issue with your computer.? I suspect the volume setting for the QDX audio output (Speaker) is most likely the issue.? I am typing this on my one W11 machine to capture the screens.? As stated in my prior email, I do not have a WSJT-X setup for this PC.

Can you verify in the settings that the QDX device appeared on this screen?


Here is the same screen when I add my Bluetooth headphones:



Note that the Headphones are added.? You can then expand the QDX (Headphone in my example) to see the volume settings for that device:



Make sure that the volume setting is at 100%.

Let us know if that solves the problem.

73
Evan
AC9TU

Okay. Now you know one thing it AIN'T!

One obscure issue with time sync:

I have a cellular internet modem (T-Mobile) and it will not allow most of these time syncs, such as Dimension4, or many others, to work. It will also not allow ftp sites to work.

My work around for this is to use a Personal Hotspot from my cell phone. Even though it uses the same cell network and the same tower, this works, while the cellular internet modem does not- go figure.?

But built in time syncs in Windows and Mac OS do work fine, tho.?
--
73, Dan? NM3A

I read this with interest a few weeks ago and would be interested in Hans' thoughts on a commutating diode across L14 and wondering if perhaps there might be a future revision to the QDX?

Check the voltage at C406. One is ground the other should be about 2.5v.

-mike/w1mt

I just tried JS8 Call. I'm still not getting any power out and seeing two flashes on the LED. I also got this error, which I have also seen in WSJT-X:

Hi Karl,

no, on my board c509 is fitted, sitting snuggly next to R510.

Paul DJOCU?

Hey, Alan. Thanks for the info--you guided me over to it perfectly. It looks like the microphone permissions are set correctly for WSJT-X.

Hey, Evan. So, two answers:

1: The wall wart says 2A. To be honest, I just assumed 2Ah, I think I just learned something. Thank you!

2: OMG...you got me a step closer!! I get about 5 watts displaying on my analog power meter that is part of my dummy load. This is the first time anything caused the needle to move!! Saying that, I'm still not getting any power out from within WSJT-X and I am still getting two flashes on the QDX' LED. I'm thinking I am still fighting an audio problem. I have no way of telling if I am receiving any audio via the QDX. I'm connected to a dummy load. I don't have an antenna here where I work.

Wayne

WB2CBA's post did not include "CAT" - just PTT through VOX.?
If you are just interested in PTT, I'd suggest USB sound cards with GPIO.?
? ? A much simpler (resistor and transistor) PTT solution which is support by most digital applications.

The digirig-mobile DOES include real CAT control.?
With that your computer can control the freq/band and any other settings that are included in CAT commands (including selectable filters, etc.).
Very reasonably priced as well!
Only down side I see is that it appears the sound card input is mono.

I have an old MicroHAM USB Interface III from about 2008 which had sound card and CAT capability.? Not sure they are around any more.
I paid a lot of money for it!?I haven't used it in years.??Gave up on it when Windows stopped supporting the USB driver.
? ?I wonder if newer Windows versions would work with it.?
? ? I'll have to give it a try.

-------
Rob KB8RCO

On 24/08/2023 13:52, Wayne Greene wrote:

Hey, Alan. Maybe? Where do I find that in win11?

Wayne,

W10 here but try entering "microphone" in the search box.
(Settings - Privacy - Microphone.)

73 Alan G4ZFQ

Wayne,

You stated, "I built my QDX for 9VDC and am running it with a 9VDC 2Ah wall wart power supply. "? Can you confirm that it is 2 amps and not 2 amperhours?? There is a difference as amperhours is the length of time that the battery will provide current depending on the amount of current drawn.? There is also a maximum current that the supply can deliver.? The best is to measure the voltage while the QDX is running.

73
Evan
AC9TU

Hi Wayne,

I do not have a Windows 11 machine configured for WSJT-X operation.? They are all Windows 10.

I used my Rev1 QDX today to see if I could find similar issues to what you are reporting.? I did see the same problem.? To resolve it, I first verified that PuTTY could talk to the QDX.? At first, it did not, as the com port changed in the last Windows update.? If the com port is not configured correctly, WSJT-X does not start the waterfall and appears to have audio issues.? To get everything working again, I had to reload the QDX firmware and restart the PC first and then the QDX.? I verified the settings in WSJT-X, and everything worked.

So the steps I recommend are:
1 - Load the latest firmware (1_10) to the QDX
2 - Power off the QDX
3 - Reboot the PC
4 - Turn on the QDX
5 - Use Device Manager to verify the com port number
6 - Use PuTTY to verify transmitter operation
7 - Exit out of PuTTY and close the PuTTY window
8 - Start WSJT-X
9 - Set any values that may have changed (Comm port)
10 - Verify receive and transmit with WSJT-X

It took me a couple of resets to get the above to work.? Something in the last Windows update messed up the comm and audio settings.

NOTE: The QDX is fussy when connecting to Windows.? The PC must be on and connected when powering on or first connecting the QDX.? It has to do with setting the USB parameters.

73
Evan
AC9TU

So, one other thing I checked based on other things I looked at in the forums related to my issue, is my input voltage. I built my QDX for 9VDC and am running it with a 9VDC 2Ah wall wart power supply. I checked the unloaded voltage and it reads 9.2 volts. Might is be possible the voltage is getting too low under load?

Wayne

Hey, Cliff. I'm not sure how to check that in Windows, either; although, everything I an see indicates the QDX soundcard is assigned correctly.

Wayne

Hey, Alan. Maybe? Where do I find that in win11?

Wayne

Roger, thanks for everything. I really do appreciate your trying.

Wayne

I have been trying to get somewhere troubleshooting why my 12v QMX will not boot or show up as a USB device. I have checked the power supply boards, which seem to be working, and have followed all the steps others in here have done to try and get theirs working, and haven't gotten anywhere.?

What can I do at this point to get somewhere with this? Is there someone around that can provide some one-on-one troubleshooting guidance??

On 24/08/2023 13:22, Wayne Greene wrote:

some stupid and rediculous sound setting in my computer

Wayne

Not microphone privacy?

73 Alan G4ZFQ

Dimension 4 is a reliable time sync software.



73

Barb WB2CBA