Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
On Fri, Apr 25, 2025 at 01:10 PM, Hans Summers wrote:
Then I expect that should also be the case in 1_01_005.
Except in the current 1_01_005 I have the same problem as everyone else, the USB device is unrecognized due to 'Configuration Descriptor Request Failed'.? The fix you just made should remedy that, so maybe my machine won't have the problem with 3 ports like yours.
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
You mnade me do it. Booted my W11 machine. Less than 1 minute to log in screen. Probably 90 seconds until I was typing this email.
Tony
AD0VC
toggle quoted message
Show quoted text
Anyway now I'm trying to boot into Windows 10. I still have the old 1TB hard disk attached to my computer though it's some years now since I booted into Windows.
We will hear from you in a few days after it finishes patching...? ;-)
For reasons best known only to itself, Win 10 didn't do any patching even though it's been years since I used it. And it even seemed to boot in only about 7 minutes which is much faster than I recall. Though still woefully slower than the 10
seconds it takes the same machine to boot into Linux.?
I'm pleased to report that setting USB Serial ports to both 1 and 2 both worked, with both serial and sound. TeraTerm is apparently what's on the desktop and I could connect to both ports with no difficulty, and sound too.?
Setting USB Serial ports to 3 did not work (as we know from 1_01_004).?
So all: please standby while I prepare and upload a .QMX file with high confidence, and my apologies for not thinking of booting my computer into Win10 until now and wasting your time on it.?
73 Hans G0UPL
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
Setting USB Serial ports to 3 did not work (as we know from 1_01_004).
But for some of us, all 3 ports were working fine in Win10 (fully patched Win10 home edition) in 1_01_004.
Then I expect that should also be the case in 1_01_005. My Win10 is very old, remember. In Linux I see the three ports and Audio no problem (and USB Flash drive, if I enable that in the firmware).?
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
On Fri, Apr 25, 2025 at 01:01 PM, Hans Summers wrote:
Setting USB Serial ports to 3 did not work (as we know from 1_01_004).
But for some of us, all 3 ports were working fine in Win10 (fully patched Win10 home edition) in 1_01_004.
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
Anyway now I'm trying to boot into Windows 10. I still have the old 1TB hard disk attached to my computer though it's some years now since I booted into Windows.
We will hear from you in a few days after it finishes patching...? ;-)
For reasons best known only to itself, Win 10 didn't do any patching even though it's been years since I used it. And it even seemed to boot in only about 7 minutes which is much faster than I recall. Though still woefully slower than the 10 seconds it takes the same machine to boot into Linux.?
I'm pleased to report that setting USB Serial ports to both 1 and 2 both worked, with both serial and sound. TeraTerm is apparently what's on the desktop and I could connect to both ports with no difficulty, and sound too.?
Setting USB Serial ports to 3 did not work (as we know from 1_01_004).?
So all: please standby while I prepare and upload a .QMX file with high confidence, and my apologies for not thinking of booting my computer into Win10 until now and wasting your time on it.? 73 Hans G0UPL
|
Re: QMX and digital modes with Win 8 and Win 10
I meant that I just used PC speakerphone - air - QMX microphone instead of USB cable to transfer audio from PC to QMX ))
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
On Fri, Apr 25, 2025 at 03:49 PM, Hans Summers wrote:
Anyway now I'm trying to boot into Windows 10. I still have the old 1TB hard disk attached to my computer though it's some years now since I booted into Windows.
We will hear from you in a few days after it finishes patching...? ;-)
?
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
I used USBTreeView to look at the QMX USB port with 004 and 005 installed. In case it might be of use, I attached the output as two files, one for 004 and one for 005.
Tony
AD0VC
toggle quoted message
Show quoted text
Hi Ludwig
I agree, something must be amiss. But somehow Linux is making sense of it and Windows isn't! Don't worry, I'll find it!
George, QMX is already a powered hub, in effect. Cascading hubs would add more variables to a mix which already has enough variables!
73 Hans G0UPL
On Fri, Apr 25, 2025, 21:15 George Korper via
<georgekorper= [email protected]> wrote:
Hi there,
Would a powered USB hub, be practical or does that add more issues??
Thank you,?
George?
K3GK
?
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
Could it be that in Windows the data and command endpoints must be allocated pairwise? Or Windows requires that command endpoints must exist even if not used.
No. Well yes... But with the COM ports = 1 setting it is supposed to replicate the precious situation.?
Anyway I found a 1 character typo, in the length of the USB descriptor, which could be the problem. Weird that Linux tolerates it. Anyway now I'm trying to boot into Windows 10. I still have the old 1TB hard disk attached to my computer though it's some years now since I booted into Windows. So I'll try and test it now .. 73 Hans G0UPL
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
Hi Tony
Well, for fun, I reinstalled 005 and ran the calibration from the front panel. Phase works better but I still have one (30 Meters) that does not complete. I went back to 004 so that I could look at the result curves. I'm not sure if you did anything with SYNC
but some of those changed as well. I will have to try manually rerunning some of them.
A problem is that everyone's machine will be slightly different. When I get the next beta out and it works on Windows I'd be grateful if you could run 30m on its own, and take a screenshot both when it is running (and DAC is say, a few hundred); and when it is completed.? 73 Hans G0UPL
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
Well, for fun, I reinstalled 005 and ran the calibration from the front panel. Phase works better but I still have one (30 Meters) that does not complete. I went back to 004 so that I could look at the result curves. I'm not sure if you did anything with SYNC
but some of those changed as well. I will have to try manually rerunning some of them.
Tony
AD0VC
toggle quoted message
Show quoted text
Hi Ludwig
I agree, something must be amiss. But somehow Linux is making sense of it and Windows isn't! Don't worry, I'll find it!
George, QMX is already a powered hub, in effect. Cascading hubs would add more variables to a mix which already has enough variables!
73 Hans G0UPL
On Fri, Apr 25, 2025, 21:15 George Korper via
<georgekorper= [email protected]> wrote:
Hi there,
Would a powered USB hub, be practical or does that add more issues??
Thank you,?
George?
K3GK
?
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
Could it be that in Windows the data and command endpoints must be allocated pairwise? Or Windows requires that command endpoints must exist even if not used.
--
73 Matti OH6BEX
|
Re: QCX-mini LCD top row is blocks, bottom row is blank
yes, I'm sure that is the case. Must have happened during the factory reset just as power dropped showing a blank LCD. I've ordered another IC2.
Jeremy
|
Re: QCX-mini LCD top row is blocks, bottom row is blank
¡°Use original IC¡± usually means that IC2 lost its EEPROM file. You may have to get a new chip to fix it. Sorry¡ Ron
On Fri, Apr 25, 2025 at 09:59 Jeremy Ollerenshaw via <ollerenj= [email protected]> wrote: Thanks Ron, I re-worked a few solder joints and was able to bring things to life. Performed alignment and places in case, but now have a couple of other issues to troubleshoot. 1) on power-up, LCD looks normal but text slowly dims to nothing and no functions work. Power-cycling right away brings up LCD with no text and no function. Waiting a few minutes to power-cycle brings up LCD with text which then dies away as before. 2) I performed a factory reset to see if that would help but now on power-up I have a LCD that is not lit but has text 'use original ic' and no functions work. I can see this is going to be a journey!
Jeremy
|
Re: QMX and digital modes with Win 8 and Win 10
Miguel, thanks for the tip on using Voicemeeter to fix the USB volume.
For some reason the VARA-HF modem software does not put full-scale audio into the QMX USB sound device (at least in Windows).
Some posters have recently mentioned using a 'speakerphone' setting in the VARA soundcard settings to boost the volume, but my VARA-HF doesn't seem to have such a setting, and I have the latest.
|
Nice.? I have had my QMX out for several SOTAs this year.? Mostly work CW.? Here is my setup.
|
First, make sure the PTT is working.
?- put qmx in digi mode, on vfo A
?- press the flrig PTT button, and see if a dot appears under the A while PTT is on
?- that means PTT is working
?- if not working, check the flrig config - PTT generic, and make sure "PTT on CAT Serial Port" is set to BOTH, with RTS and DTR OFF.
?
Then make sure transmit audio level from PC is sufficient to drive the QMX:
?- set windows volume setting for the QMX playback device to 100%
?- in the FLdigi main window, bottom status border, near the right-hand-side, there is a "tx level attenuator" setting which by default is set to some number other than zero.? Set it fully up to 0.
?- in the FLdigi main window, top right, turn off both RxID and TxID.? Press 'Tune' there (with dummy load or matched antenna attached to QMX).? With that 'Tune' on, you should see first two dots appear under the A in the QMX display, then it should change to a line.? Two dots mean PTT worked and audio is being received by QMX, the line means that the audio is strong enough for digi mode transmit, and it should be transmitting full power.
?
If you plan to run RTTY, make one more FLdigi setting change: Config -> Modem -> TTY -> Tx:? uncheck the "Shaped Tx" button, otherwise RTTY Tx will not work (external shaping interferes with QMX internal shaping).
?
Now it should all work in digi mode for FSK types.? And you can also put it in SSB mode, and it will work on the other types.? But do the setup in digi mode, because it is easier to see that things are set up properly.? Digi mode is still preferred (will give better performance) for all single-tone-at-a-time modes (RTTY, MFSK*, etc), but SSB mode is required for all phase-shifting (PSK) or multitone types.
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
Hi Ludwig
I agree, something must be amiss. But somehow Linux is making sense of it and Windows isn't! Don't worry, I'll find it!
George, QMX is already a powered hub, in effect. Cascading hubs would add more variables to a mix which already has enough variables!
73 Hans G0UPL
On Fri, Apr 25, 2025, 21:15 George Korper via <georgekorper= [email protected]> wrote: Hi there,
Would a powered USB hub, be practical or does that add more issues??
Thank you,?
George?
K3GK
?
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
Hi there,
Would a powered USB hub, be practical or does that add more issues??
Thank you,?
George?
K3GK
?
|
Re: #qmx SSB Firmware beta 1_01_005 release
#qmx
One more information:
For FW 003 also a working composite device with the same VID and PID is shown.
So both the composite device and the underlaying device was found.
?
For FW 005 only the composite device was found. Maybe no announcement of the underlaying devices or announcement not in the right form?
?
73 Ludwig
?
|
Dj Merrill
Ronald Taylor
Brien - KE7WB