I'm not sure what you mean. There is a setting in the keyer menu for straight key. The cadence is established by the movement of your wrist and finger.
--
73, Dan - W2DLC

I tried using my Navy Flame Proof key with a QCX-Mini last night and noticed that it was keeping the cadence slow, I don't know how to describe it, but when I tried to key fast it felt slow. Is there a good setup for using a straight key? Using a Paddle in IambicB works great. Any tips would be appreciated.

On Thu, Jul 11, 2024 at 09:56 PM, Steve N2IC wrote:

I have proven that it is possible to fry IC402 with too much RF on the input side. :(

Did you have an antenna connected to your QMX while you were transmitting with another radio ?

No, but there were a few times the SWR protection triggered while tuning a random wire that starts a foot a way or so.

Timmy,

Who cares.
That amp from Diz is rather nice but does not work at all well on 15 or 10M.

So stay on topic and help the gentleman with his QRPL 10W amp.

--
Allison
------------------
Post online only,?
direct email will go to a bit bucket.

First you need to put a load on it for safety.?
Ground the TX enable line or the bias setting will not happen.
The TX line is so the amp can be shut down for RX.


--
Allison
------------------
Post online only,?
direct email will go to a bit bucket.

David,

Sorry, it should read “in the range 1400-1600Hz”.

John
G4YTJ

开云体育

John thanks.? ?I have the time to within a second.? What should the on screen frequency be?? ? (by band if you can!)

Make sure that the enamel? is completely removed in the areas where you are going to solder. If the holes they are going into are plated through holes? ie PTH then as a temp measure you can use a finer gauge wire such as stripped out? Cat 5e wire which is pure copper once the PE insulation is removed andtack the copper lead outs of the transformers just to the top pad. Then once the whole thing is working you can move the lead out wires? back to fully installed.

?

The? wire going from the BN transformer near words? that look like? C202 on solder mask looks very suspect.? You can heck as soldered connections if you remove a a little more insulation on the magnet wire of the coils so can get one DVM probe in there and one direct to the PCB rondel to check? continuity.? ? If there is ANY doubt at all that the PTH are really? plated through then have enough tinning on the copper? that you can solder both Top? and BOTTOM side? (taking care not to burn components );? ?that will fix the bastardo.?

?

But you would then never know which particular through hole had the issue.? Never mind - it's a one off not a production jobbie.?

I appreciate you spelling out the additional instruction pages. That allows me to print off my additional resources to add to my already existing manual without comparing page by page.

Keep up with the great work and thank you!

Greg?

Thank you for replies.

I desoldered both IRF510s and checked them (like in this video):

They both seem OK and have very close numbers when I measured.

After that I gave 13 volts power to PA and measured the voltage on empty GATE holes (As shown in the photo). When pots are fully CCW closed, it is 0 volts. When I open pots CW fully, I read 5 volts each. So, bias system and MOSFETs are working.

I now focused on output transformer and going to remove it and check with all other windings and solderings because I suspect that my soldering work may poor.

I will write again soon. Thanks.

There's an X shown? under the? dropper to GND front end of regulators (as per schematic) .? That's? in fact a form of PTT line.? My poor eyes did not see that first up and of couse I did not RTFM .. what sort of moron do you think I am? ??

? If that had a BS 170 or even 2n7000 squeezed in you 'd have a 5V active PTT (isolated system) .? I'll dig out a very nice? Fr design which sshows? a carrier operated relay system (COR)? basic design for those who well? want to be different.? Remember COR? can be problematic with SSB as when voice levels diminish at some point the? COR relay / mosfets are going to drop out.? With maintained carrier systems like AM and NBFM this is never an issue.

Here is Anker Soundcore Mini.

You might see this speaker in many videos with QRP rigs of different radio operators

I also have got it, very like how it sounds and keeps battery.

Great video Hans, enjoyed it immensely. Many thanks.

Gary.
G7TOK

The wiki page QMX CW AGC and Clicks has been updated by Andreas DM7AK <mail2dm7ak@...>.

Reason: add official default settings

Compare Revisions

You write: When I start to turn one of the pots, it is still 140mA stable.
That suggests to me that you expect the current to increase immediately at the start of the pot. It won't but at a certain voltage on the gate, the IRF510 will start to draw current. Be careful, once it starts it will increase rapidly. At that point you may have to go slowly up and down to get 125mA in each.
73 Brian VK4BAP.

Well, RTFM and it states ground the tx pad to turn the amp on, days wot that is boy.
--
The universe is made up of Protons, Neutrons, Electrons but contains only one M0RON.

Ground tex before? measuring? Tx current Draw : " Wot Dat? Boy ? " **

?

I think you are thinking of the type of PA where the? bias to the high power
Fets is only applied in? Tx mode. The Ten W linear is a straight Pallet amp without even Rx Tx control -that''s? a user hack if the user wants it - there is nothing to ground to force it to Tx mode.? I sent a? Schematic in as? separate post.?

** NZ slang from? out in the boondocks no offense meant.

Schema for reference and Sh_ts and giggles

I had the same problem. Put ferrite clip on chokes on USB leads at both ends of USB leads fixed my problem. Works for Win and Rpi now.?