开云体育

In my desperate rush to get back home this weekend and into the shack to change the power supply (thinking it could be a unstable power source and hence being the cause of the problem), I connected my

Thanks for the extremely helpful reactions ! I'll go for 580Hz then. I guess the announced additional configuration menu item on DSP centre frequency is not yet in the current f/w ...? 73, Enno, PF5X

Here are Hans answers to me when I wanted to go for 450 Hz: Hello Rolf ? Yes, there should not be any problem doing that. As I noted in the manual, the CW filter in the QCX is a slightly modified

I did it for 480hz without any changes in audio phase shift frequencies, unwanted side band suppression is still absolutely amazing. Greg w3nw --------------------------------------------

I find the simplest way to control “flying pins” is to position your side cutter on the pin and simply place a fingertip on the pin to be cut. This dampens the “spring” effect and the will

Hi all, I am awaiting my QCX #1229 (per 25 oct 2017, it is the next one to ship ... !). Meanwhile I am preparing a few things and one of them is changing the center frequency for the CW filter. I have

The probable solution is in this thread. /g/QRPLabs/topic/qcx_start_up_issue_correct/6252498?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,0,6252498

Hilarious, many laughs, thanks folks... Hans, a great explanation of bugs and we're in awe at the QCX and it's development. I look forward to attaching two bugs to the QCX soon, one is from the 1940s,

Enjoyed that..... Who you are, what you do and why you do it came across very well Hans.. Thanks for the kits Phil? G4JVF

Hi all A 20-minute interview recorded at Newark UK National Hamfest on 30-Sep-2017, about QRP Labs and the QCX transceiver. It is in the last 20 minutes of ICQ Podcast episode 252, you can listen at:

Hi Daniel See QCX manual page 115 re "Tuning Clicks" 73 Mike G0CVZ

Hello Micheal. I had a similar problem in 20m trying to get the drift stable. Before doing anything to the rig, I used to get awful drift. Really to the point of getting zero spots. -4 -3 were very

Well that's promising. The first 8 spots after getting the PA lined back out had 0 drift. Maybe the brass donut did the trick. on 80m the same rig was drifting between 1 and 2.

Well... I put the U3s on the bench, hooked up the oscilloscope, and sure enough, output with (3) BS-170's and a little over 8V was only a little over 100mW. I moved it up to 500mW. We'll see how it

Well after connecting the control wires and then checking everything again to make sure all was what it was supposed to be I connected the U3S to a dummy load and hit the switch. Everything powered

David Has it started properly at all yet? I had mine going but was having the issue of not starting first time but only on second power on. At one point when I was powering on and off to test possible

I’ve tried the fix but no luck. I have two lines of bars with a pulsing thin line that moves up/down through the bars.. Thinking IC2 is not doing its job, but the pulsing makes me think there is

Should I reset my PA bias after switching bandpass filters?? I wouldn't think so. I ask because I had about 500mW with the 80m filter last night and now on 30m I get 100mW. I set the bias with my

OK Hans, I will check my WSPR signal by myself. Thanks. Hidehiko.

Are you still having issues what is your exact fault BR Andrew Sent from my Windows 10 phone Sent: 25 October 2017 22:10 To: [email protected] Subject: Re: [QRPLabs] Problems with Relay Kit So as a