开云体育

Hi all, Additional info. as follows; Transmit monitor Blue LED is connected to the PIN #2 of the PIC chip. There appears about 2.5V-DC when transmitting. ja9mat Hidehiko.

Hi members, I've finished to build yesterday. I also put some photos in "JA9MAT" photo folder. My Modification are follows addition; 1)The PIEZO monitor speaker 2)The transmittig Blue LED

No problem. Send me an e-mail once you are ok. I have a beacon that I try to run every night between 1500z (when I go to bed) and 0000z. My signal has been received by ZL2IK already and when I was

Hide, I can turn on a grabber on 30m if you want tonight from around 1500z to 0000z monday. Drop me a direct e-mail if you are ok. 73, Yan - XV4TUJ

Hi friends, I've uploaded my mod. of the QRSS TX kit. I added the BCD Switch to select the 8-transmitting mode. It works fine without adding the pull down resisters. Please see the photos into

Hi. Thanks for the references you gave. I measure my DC consumption and it is around 137mA at 5,5V with 100mW RF out. That confirm my 2N7000 could draw more than expected and why it is hotter than

Mine draws 65 - 70mA at 5V for 50mW out. When I increased the power to just below 100mW (which was the peak in my case) it increased to 120mA. Increasing the bias voltage beyond that it was more

Hi Stephen, Yes I checked R6 already and it is 6k8. R8 is closer to 1,8K than the stated 2,2k in the schematic. The closer potentiometer I have in my spare box is 5k. I tried to had 1k to R6 but

Mine draw around 85 mA at 5 volts. Since you are at 6+ volts, I'd say your current is normal. Mike n0qbh

I have now managed to complete my 30m QRSS kit and was wondering how much current they should draw from the supply. Mine pulls roughly 100mA from 4 x AA batteries in series. Does that sound about

Hi Yan, Can you check that R6 is 6K8 please. Regards, Steve -- It is vain to do with more that which can be done with less.

Hans...& others These QRSS beacons (and the grabbers) seem to be popping up on many bands and on many frequencies. This seems to suggest that we each need QRSS Beacon transmitters for all bands,

Hi all, I lied about the pull ups....i really meant pull downs...sorry. Steve -- It is vain to do with more that which can be done with less.

Hi all Just some comments regarding the recent keyer chip thread: 1) Do NOT use 10K pull-ups! It won't work! You need pull-DOWN's! Not up! If you see this problem, then you can connect a 10K

Hello Neil and Paul, I had the same problem. Once I grounded the unused pins as Hans suggested all was fine. 73, ---Paul AK1P ________________________________ To:

Neil I have gotten the same thing with my PIC keyer chip. Hans suggested grounding all the unused pins on the PIC. With the jumper for 3Sec dots it seems to send the call at 12 WPM once every few

Hi guys, I think there is some variation in the ATTiny13 keyer chips. having programmed over 150 of them with the software using exactly the same programming arrangement I would say 1 in 10 chips

All, This is very interesting because I had same issue. I was also just monitoring my signal and mine just set the NDE of M0NDE fast then carried on ate qrss. Please confirm connection you made

Neil G7AQK I had to add 10K pull-up resistors to the speed selection jumpers. This solved my problems with unreliable setting of speed, and other strange behavior. Arv K7HKL _._

I just finished putting my 30m QRSS kit together yesterday evening (certainly more interesting than X Factor) and every thing seems to be functioning. I have run the keyer in its default 12 WPM