?

Hi Keith

Can you give me a photo of how it looks with the digit missing off the right? ?Or, write out exactly the display, character by character? Then I can try to get it corrected/moved.

73 Hans G0UPL

On Wed, May 22, 2013 at 5:24 PM, Keith Maton <nentecular@...> wrote:

?

Hi Hans,

I've been doing some testing and changing the SPEED parameter so that my callsign fits nicely in ten minute frames - If I set speed to 10 then my callsign fits with 20 seconds to spare so that's absolutely perfect.

However, in FSKCW10 mode, while idle between frames, the far right digit of the time is missed off because the clock has moved to the right. ?So it shows 16:24:1?

There are a couple of spaces to the left of the time display, could you shift the clock one character to the left so that it will fit when using a SPEED parameter that runs into double figures please?

Thanks,

73 Keith, G6NHU

On 19 May 2013, at 12:46, Hans Summers <hans.summers@...> wrote:

?

All

My email box is full of millions of emails and so I thought, to clarify all my and your thinking, one big post should list it all out. Summarise where we are with it all. If I am missing anything, please let me know.?

Enhancement requests: firstly, there are a number of new requests (other than the GPS and 10m issues, of which more later). I'll attempt to put as many as I can in the v2.02 firmware version. These are as follows:

1) Support for the WSPR-15 mode (useful for LF WSPR)

2) Adding 1 digit to the GPS Baud setting, so the kit can be used with 115kbps (also requested for an Ultimate1 v1.09 enhancement)

3) Allowing the / character in messages for FSKCW, QRSS, DFCW, CW modes

4) Removing the 42.5MHz (approx) upper frequency limit

5) Fix a couple of occasional cosmetic bugs appearing in the Time-setting menu item

6) Move the Time setting to the front of the menu items, as it is used more often than any others when using the WSPR mode and everything is already set up (e.g. for correcting the time, when no GPS is being used).

New shop items requests: I have had requests to add the following items to the shop:

1) Selling BS170 transistors separately to the main kit

2) Sell the 4-pin headers and sockets separately to the main kit

3) Make available LF band modules for 475kHz and 135kHz?

10m etc issue: The summary of this issue is that it appears that there may be an arithmetic precision issue in the code for setting the DDS frequency word, which becomes apparent when the amount of shift is small in relation to the output frequency. So I need to change that part of the code which deals with calculating the DDS frequency word. Although, it remains considerably confusing because some people appear to have had some 10m WSPR spots. Perhaps they were lucky to choose frequencies which happened to work.

GPS issue:?There appears to be an issue with some GPS modules which worked in U1 but not U2. There have been some reports of people using GPS with no trouble, with Ultimate2. My current theory is that the short pulse width from some GPS modules is interfering with, or being interfered by, the incoming serial data stream. So I need to look at the differences between how I did the GPS work in U1 and U2.

Other comments:

1) People have remarked on the frequency switching transients when the DDS frequency changes. I think this is a minor thing which if all else was well, should not interfere with kit operation or WSPR decode etc. However, I checked in this area of the code and I did actually find that I think the frequency is being briefly set to zero before the new frequency is set, and that this might be making the short frequency glitch longer than necessary. So in v2.02 I will attempt to tidy that up.?

2) Regarding the blue potentiometer on the DDS module. When the modules arrive from the manufacturer, it appears that the blue potentiometers are not set up - that manifests itself as no output squarewave from the comparator. Before packing the kits, I individually tested every single one of the 200 DDS modules. 29 were discarded as their stability was found to be unsuitable. The rest of them, the potentiometer was adjusted for best output on 30m. So I thought that it should not need further adjustment by kit builders. However, it is possible that the setting on 10m might be more critical, or different, from the optimum setting on 30m - as some constructors have found out and advised.?

3) Someone mentioned that the maximum output frequency of the comparator is only 1MHz. However I don't think that this is correct. The specification of the DDS module from the manufacturer sometimes says that the squarewave output is valid up to 1MHz. But the DDS module output is straight from the comparator output pin of the AD9850 DDS chip and I don't see anything in the AD9850 datasheet about any upper frequency limitation.?

4) Feedback on the question of whether to reverse the BS170 transistors in the new PCB, or reverse the silk screen, or leave as is - was rather (surprisingly) mixed. So I still have to consider that one.?

?

5) I had some delay with ordering all the components, because PayPal rather unreasonably decided they should block my account to make sure I'm not a money launderer. That's all resolved now so I can continue with ordering the remaining components for the next set of 200 kits.?

I think that's about it. Let me know if I have missed anything out.

73 Hans G0UPL