Re: Suppressing RF noise - ambient mics into CODEC (on headphones)
Here's a slightly better quality attachment of my mic wiring diagram. (sorry for the pixelation).
|
Re: Suppressing RF noise - ambient mics into CODEC (on headphones)
Hi Jerry, Thanks for responding! The mics signals are connected to the inverting inputs of the PGAs on each channel on the CODEC. Non-inverting inputs of PGAs are set to connect internally to VMID. They also have the necessary passives in-between the actual mic pads and the codec inputs. Power is coming from the output of a dedicated 3.3V LDO voltage regulator on the WM8960 breakout (AVDD pin), which in my setup is getting powered upstream by 3 AAA NiMH batteries at the VIN pin on the breakout.  Thanks again! Pete
|
Re: Suppressing RF noise - ambient mics into CODEC (on headphones)
Hi Pete,
Welcome to the group!? Looks like a very cool project.
If I could make one suggestion with respect to using this group, it would be to take care not to send huge attachments out to the group.? We have plenty of file space for sharing such things.
Thanks,
-Scott
toggle quoted message
Show quoted text
On 1/22/24 20:49, Pete Lewis wrote: Hi There folks!
I've been experiencing some RF interference on some PUI AOM 5035L mics into a WM8960 CODEC. Any advice on how to mitigate this would be much appreciated!
Sorry for the long message, but here it goes...
I like these mics for my application (loud drums) because of their really high AOP (135dB) and big SNR (75dB). For the most part, I've been pretty happy with my project <>. In my basement, and around my house, I experience superb sound quality with no RF interference. But at my favorite drum rehearsal spot (drumbox in Lafayette <>), I am experiencing RF noise. I will attach a recording I made of the sound, if your curious or might be able to help identify the kind and/or source.
I've tried many things, including the following:
1) Turning off all bluetooth and I2S communications on my microcontroller. It is simply controlling the PGA gains on the mic inputs and passing that through the CODEC in the analog bypass paths. This is less likely to be the culprit, because in my basement I don't experience the RF interference (even with BT/I2S running).
2) Upgrading all audio and data cables to shieled (Mogami W2697).
3) Wrapping a GND wire around the small connection from CODEC to MIC (which includes it's required pull-down resistor and in-series cap mini-PCB).
4) Putting my entire "right ear" electronics inside a box that I covered with copper tape (two layers). FWW, this stops any RF noise introduced by when I hold my RC airplane transmitter nearby. But doesn't stop the drumbox RF noise. Which I'm guessing is a stronger RF signal (?).
5) Putting a separate CODEC in the left ear, in hopes that the shorter distance of the left mic and left CODEC would help. But still no luck. I later found out that the RF noise can also enter my right ear signal - depending on the rotational position of my head (while wearing the headphones).
None of my efforts have seems to stop or reduce the RF interference into my system at the drumbox. The owner has let me know that they wirelessly beam their Wifi from the main building out to the rehearsal room (across the parking lot). So my guess is that this might be the cause.
Any thoughts would be greatly appreciated and thanks in advance!
Cheers,
Pete
PS there is much more info on my tutorial <>, but these two diagrams show the bulk of the project:
And here are my attempts at protecting with copper tapped box and wrapped GND wires:
--
---- Scott Helmke ---- scott@... ---- (734) 604-9340 ----
"I have ceased distinguishing between the religious and the secular,
for everything is holy" - Joe Henry
|
Re: Suppressing RF noise - ambient mics into CODEC (on headphones)
sounds like maybe cell phone close by?
Ferrite beads.?
Ferrite Clamshell EMI Filter?
toggle quoted message
Show quoted text
On Monday, January 22, 2024 at 10:22:33 PM EST, Jerry Lee Marcel <jerryleemarcel@...> wrote: Le 23/01/2024 ¨¤ 03:49, Pete Lewis a ¨¦crit?: I've been experiencing some RF interference on some PUI AOM 5035L mics
into a WM8960 CODEC. Any advice on how to mitigate this would be much
appreciated! You don't say how they are connected to the CODEC. How are they powered, is there an active circuit?
|
Re: Suppressing RF noise - ambient mics into CODEC (on headphones)
Le 23/01/2024 ¨¤ 03:49, Pete Lewis a ¨¦crit?: I've been experiencing some RF interference on some PUI AOM 5035L mics into a WM8960 CODEC. Any advice on how to mitigate this would be much appreciated! You don't say how they are connected to the CODEC. How are they powered, is there an active circuit?
|
Suppressing RF noise - ambient mics into CODEC (on headphones)
Hi There folks! I've been experiencing some RF interference on some PUI AOM 5035L mics into a WM8960 CODEC. Any advice on how to mitigate this would be much appreciated! Sorry for the long message, but here it goes... I like these mics for my application (loud drums) because of their really high AOP (135dB) and big SNR (75dB). For the most part, I've been pretty happy with . In my basement, and around my house, I experience superb sound quality with no RF interference. But at my favorite drum rehearsal spot (), I am experiencing RF noise. I will attach a recording I made of the sound, if your curious or might be able to help identify the kind and/or source. I've tried many things, including the following: 1) Turning off all bluetooth and I2S communications on my microcontroller. It is simply controlling the PGA gains on the mic inputs and passing that through the CODEC in the analog bypass paths. This is less likely to be the culprit, because in my basement I don't experience the RF interference (even with BT/I2S running). 2) Upgrading all audio and data cables to shieled (Mogami W2697). 3) Wrapping a GND wire around the small connection from CODEC to MIC (which includes it's required pull-down resistor and in-series cap mini-PCB). 4) Putting my entire "right ear" electronics inside a box that I covered with copper tape (two layers). FWW, this stops any RF noise introduced by when I hold my RC airplane transmitter nearby. But doesn't stop the drumbox RF noise. Which I'm guessing is a stronger RF signal (?). 5) Putting a separate CODEC in the left ear, in hopes that the shorter distance of the left mic and left CODEC would help. But still no luck. I later found out that the RF noise can also enter my right ear signal - depending on the rotational position of my head (while wearing the headphones). None of my efforts have seems to stop or reduce the RF interference into my system at the drumbox. The owner has let me know that they wirelessly beam their Wifi from the main building out to the rehearsal room (across the parking lot). So my guess is that this might be the cause. Any thoughts would be greatly appreciated and thanks in advance! Cheers, Pete PS there is much more info on , but these two diagrams show the bulk of the project:   And here are my attempts at protecting with copper tapped box and wrapped GND wires:   
|
Microtech Gefell MV203 Circuit/Repair
Hello, A while back I purchased a used MTG MV203 measurement mic to use as comparison/testing for any of my future projects. After researching the MTG documentation I built a rack-mounted power supply/preamp to go with the mic. Everything was working fine (PSU functioned nicely & super clean/healthy output from the mic). I moved the PSU into a new enclosure to make things more portable and started having issues with the mic. Sometimes I would get no output, sometimes very distorted, sometimes functioning perfectly. After thoroughly troubleshooting my PSU I found no issues with it at all, which led me down the harrowing road of cracking the mic body open and prodding around with my DMM. Here are pictures of the internals and my best shot at the schematic. Output was disconnected to verify the cable was not causing issues. Had to replace a 6k8 resistor that took flight when I was desoldering the adjacent mystery component.?   I used the component codes, DMM, and educated guesses to determine most of the components and I plan on measuring the unlabeled caps.  I'm fairly confident the High Z section under the resin is two 10G resistors in series and a 0.2 pF cap (input impedance is specified at 20G and 0.2 pF). However, I am not sure what the black mystery components are. Intuition tells me they are resistors, but they must be on the order of >>10M because my DMM cannot read them. I will have to carefully remove them and employ something like to measure them on a separate board.? Luckily I had also taken a look inside while it was working. I know from my first measurements that, when functioning, the output sits at around 65V DC offset. It now sits around 40V DC (sometimes as low as 24V) and I measure no signal regardless of sound source.? Prime suspect is the 1uF tantalum cap as I understand they are prone to damage and considered somewhat unreliable. The dual diodes, MOSFET body diodes (not sure I understand why they are used here), and Both BJTs measure ok with the DMM diode mode. I'm posting this here mostly for general interest, but if anyone has suggestions on troubleshooting the circuit I would greatly appreciate any insight.? ? ?
|
Re: Bamboo housing for nature recordings
That?2549?will work just fine
Hi Jules
Interestingly, only two balanced microphone cables are available on the Japanese Mogami website. The one that comes close to your recommended wire (Mogami W2697) at ?has the item description Mogami Part No.2549. The specifications are slightly different and can be found at (contains English descriptions...). I'll order this one.
Heinz
-- Best Regards,
Jules Ryckebusch
214 399 0931
|
Re: Bamboo housing for nature recordings
Thank you, Sey. It seems our emails just crossed. :-)
|
Re: Bamboo housing for nature recordings
Hi Jules
Interestingly, only two balanced microphone cables are available on the Japanese Mogami website. The one that comes close to your recommended wire (Mogami W2697) at ?has the item description Mogami Part No.2549. The specifications are slightly different and can be found at (contains English descriptions...). I'll order this one.
Heinz
|
Re: Bamboo housing for nature recordings
Take a look at the official stores that distribute Mogami:
Also this:
And this
Good luck!
Yep! It's funny sometimes. It may be that the item name is slightly different here. It wouldn't be the first time. I'll find it out or find a similiar one. :-)?
The electronic shops in Akihabara are interesting, I've been there once in 2016. But because it's so famous and a tourist attraction, it's way too expensive, which is a bit of a shame. Historically and from an electronic perspective it is definitely an interesting place.
Heinz
|
Re: Bamboo housing for nature recordings
Yep! It's funny sometimes. It may be that the item name is slightly different here. It wouldn't be the first time. I'll find it out or find a similiar one. :-)?
The electronic shops in Akihabara are interesting, I've been there once in 2016. But because it's so famous and a tourist attraction, it's way too expensive, which is a bit of a shame. Historically and from an electronic perspective it is definitely an interesting place.
Heinz
|
Re: Bamboo housing for nature recordings
LOL, Mogami is from there. You?should be able to get it. Also there are little electronic shops in?Akihabara, they will carry similar wire. Although I haven't?been there in 7 years.?
Jules -- Best Regards,
Jules Ryckebusch
214 399 0931
|
Re: Bamboo housing for nature recordings
|
Re: Bamboo housing for nature recordings
Where are you globally? Best Regards,
Jules Ryckebusch?
toggle quoted message
Show quoted text
On Jan 22, 2024, at 06:57, Heinz <heinz.hartfiel@...> wrote:
? Thank you both, Jules and Jerry!
Your information was very helpful. I'm currently creating the order and had already a 50V capacitor on the list. The Mouser 3.3uF capacitor you mentioned in your Instructable recommendation has a 22 week delivery time in our area. The Digikey is available!?
What I couldn't find is the?Mogami W2697. I'll look for an alternative.
Thank you again!
Heinz
|
Re: Bamboo housing for nature recordings
Thank you both, Jules and Jerry!
Your information was very helpful. I'm currently creating the order and had already a 50V capacitor on the list. The Mouser 3.3uF capacitor you mentioned in your Instructable recommendation has a 22 week delivery time in our area. The Digikey is available!?
What I couldn't find is the?Mogami W2697. I'll look for an alternative.
Thank you again!
Heinz
|
Re: Bamboo housing for nature recordings
Jerry gave a great synopsis. I give a component recommendation?in the Instructable. But in essence you what?1% metal film 1/4W resistors. They have been around a long time and replaced the carbon comp ones of my youth. For capacitors, a low leakage electrolytic works great. The key is the voltage rating. If an electrolytic?is charged above its nominal voltage rating it will sooner than later fail. Initially?it will?"leak" and cause all sorts of noise issues. We are dealing with 48-Volts at maximum so the closest higher nominal rating is 63V. Yes, there are 50V ones but price and size differences are marginal.?
Depending on where you are Mouser has these:?
Digikey has these:?
Jules
Thank you for your feedback and all the details! In particular for the link to , which seems to be inspiring and informative when it comes to mic housings.
?
I'm going to order a few balanced PUI pairs and start experimenting with the PiP version and different bamboo housings. I'll keep the group up-to-date about the progress.
?
When it comes to the simpleP48 version and in terms of recording quality, does it matter which kind of resistor or capacitor to use? E.g. MFR versus CFR resistors, aluminum electrolytic capacitor versus ceramic or tantalum, to name a few? There are so many types and vendors, it seems to be a philosophy in itself. Any recommendations?
?
Sometimes I get lost in details. ¡°Keep it simple¡± but not simplistic seems to be a good starting point. Special thanks to the author Jules Ryckebusch for making his Instructables available to the public!
-- Best Regards,
Jules Ryckebusch
214 399 0931
|
Re: Bamboo housing for nature recordings
Le 22/01/2024 ¨¤ 06:29, Heinz a ¨¦crit?: When it comes to the simpleP48 version and in terms of recording quality, does it matter which kind of resistor or capacitor to use? E.g. MFR versus CFR resistors, Not much difference in terms of performance. Metal-film may be marginally lower noise when DC is applied, which is the case for Simple P48, and may have more long-term stability and durability. aluminum electrolytic capacitor versus ceramic or tantalum, to name a few? T Quite often, value dictates technology. Capacitors in the 1-100uF range are necessarily electrolytics. Tantalum is a form of electrolytic, but are to be avoided in audio circuits. Very low value types are most often ceramic? Among them C0G/NP0 are very stable and almost distortionless. For typical 10-500nF, film caps are preferrable. High-density ceramic (X7R, Z5U) are good for power rail decoupling, but have hgh distortion in other positions. here are so many types and vendors, it seems to be a philosophy in itself. Not a philosophy. It's the need for adequation. These are broad strokes. YMMV.
|
Re: Bamboo housing for nature recordings
Sidebar Reply - Many thanks for your feedback! You might also like .?He is a scientist and researches the synchronous flashing patterns of fireflies almost every year in early summer. It was an honor to contribute some of my river recordings to the light-sensitive videos he filmed. Please enjoy!
I'm not well equipped for harsh conditions but I will give it a try to record the waves and the rhythm of the seaside! I'll let you know when the recording is online.
|
Re: Bamboo housing for nature recordings
Thank you for your feedback and all the details! In particular for the link to , which seems to be inspiring and informative when it comes to mic housings.
?
I'm going to order a few balanced PUI pairs and start experimenting with the PiP version and different bamboo housings. I'll keep the group up-to-date about the progress.
?
When it comes to the simpleP48 version and in terms of recording quality, does it matter which kind of resistor or capacitor to use? E.g. MFR versus CFR resistors, aluminum electrolytic capacitor versus ceramic or tantalum, to name a few? There are so many types and vendors, it seems to be a philosophy in itself. Any recommendations?
?
Sometimes I get lost in details. ¡°Keep it simple¡± but not simplistic seems to be a good starting point. Special thanks to the author Jules Ryckebusch for making his Instructables available to the public!
|
Pete Lewis
Sey