开云体育

Upgrading

Steven DAntonio All Messages By This Member #154812 I just upgraded to R3.043.066 (from R2), I'm getting an error that says "radius at end of arc differs from radius to start, block =G02..." I downloaded the more recent R3 from Artsoft and the? fix log shows nothing after R3.043.62.? I can go back to R2 if need be, but I'm hoping I don't have to. This code runs under R2.? Code generator was RhinoCAM 2017.? I'm running under win XP SP 3 since my computers with an LPT1 port with not support anything higher. I'm seeing this error with every piece of code I have tested so far, all of which ran under R2 without issues. Here is a snippet of the code (bold line is the one that crashes) G00 G49 G40.1 G17 G80 G50 G90 G20 (Setup 1) (Work Zero) (2 1/2 Axis Profiling) M6 T2 M03 S20000 G00 Z1.0466 X1.3373 Y-0.0609 G01 Z-0.1515? F120.0 X1.1529 Y-0.0778 X0.9299 Y-0.0944 X0.7066 Y-0.1074 X0.4832 Y-0.1169 X0.2596 Y-0.1227 X0.1105 Y-0.1246 X-0.1106 X-0.3484 Y-0.1208 X-0.5861 Y-0.1130 X-0.8236 Y-0.1011 X-1.0609 Y-0.0851 X-1.2979 Y-0.0651 X-1.5346 Y-0.0410 X-1.7707 Y-0.0129 X-2.0064 Y0.0192 X-2.2415 Y0.0553 G17 G02X-7.7519Y4.4694I0.9620J6.8475 X-7.4781Y9.3650I5.8485J2.1283 X-6.1583Y11.1056I6.2570J-3.3735 G01 X-5.9731 Y11.2914 G03X-5.4021Y11.9392I-5.5788J5.4928
Steven DAntonio All Messages By This Member #154815 And here were going to have another embarrassing moment.? After I loaded up my profile it all started working and didn't generate these errors (so far, still rigorously testing it)
chuck All Messages By This Member #154840 开云体育 Steve, been a while since I ran mach3 but there is a setting that has to do with I J K moves if I remember its a check box in one of the settings page. Chuck On 4/4/2021 10:06 AM, Steven DAntonio wrote: toggle quoted message Show quoted text I just upgraded to R3.043.066 (from R2), I'm getting an error that says "radius at end of arc differs from radius to start, block =G02..." I downloaded the more recent R3 from Artsoft and the? fix log shows nothing after R3.043.62.? I can go back to R2 if need be, but I'm hoping I don't have to. This code runs under R2.? Code generator was RhinoCAM 2017.? I'm running under win XP SP 3 since my computers with an LPT1 port with not support anything higher. I'm seeing this error with every piece of code I have tested so far, all of which ran under R2 without issues. Here is a snippet of the code (bold line is the one that crashes) G00 G49 G40.1 G17 G80 G50 G90 G20 (Setup 1) (Work Zero) (2 1/2 Axis Profiling) M6 T2 M03 S20000 G00 Z1.0466 X1.3373 Y-0.0609 G01 Z-0.1515? F120.0 X1.1529 Y-0.0778 X0.9299 Y-0.0944 X0.7066 Y-0.1074 X0.4832 Y-0.1169 X0.2596 Y-0.1227 X0.1105 Y-0.1246 X-0.1106 X-0.3484 Y-0.1208 X-0.5861 Y-0.1130 X-0.8236 Y-0.1011 X-1.0609 Y-0.0851 X-1.2979 Y-0.0651 X-1.5346 Y-0.0410 X-1.7707 Y-0.0129 X-2.0064 Y0.0192 X-2.2415 Y0.0553 G17 G02X-7.7519Y4.4694I0.9620J6.8475 X-7.4781Y9.3650I5.8485J2.1283 X-6.1583Y11.1056I6.2570J-3.3735 G01 X-5.9731 Y11.2914 G03X-5.4021Y11.9392I-5.5788J5.4928
Stephen Muscato All Messages By This Member #154841 Could it be here? ????Ports & Pins ????Turn Options ??? "Reversed Arcs in Front Post"? is it checked?? I had a problem a long time ago and I may have unchecked this box to fix it. Steve On Tuesday, April 6, 2021, 3:59:29 PM CDT, chuck via groups.io <chuckels@...> wrote: Steve, been a while since I ran mach3 but there is a setting that has to do with I J K moves if I remember its a check box in one of the settings page. Chuck On 4/4/2021 10:06 AM, Steven DAntonio wrote: I just upgraded to R3.043.066 (from R2), I'm getting an error that says "radius at end of arc differs from radius to start, block =G02..." I downloaded the more recent R3 from Artsoft and the? fix log shows nothing after R3.043.62.? I can go back to R2 if need be, but I'm hoping I don't have to. This code runs under R2.? Code generator was RhinoCAM 2017.? I'm running under win XP SP 3 since my computers with an LPT1 port with not support anything higher. I'm seeing this error with every piece of code I have tested so far, all of which ran under R2 without issues. Here is a snippet of the code (bold line is the one that crashes) G00 G49 G40.1 G17 G80 G50 G90 G20 (Setup 1) (Work Zero) (2 1/2 Axis Profiling) M6 T2 M03 S20000 G00 Z1.0466 X1.3373 Y-0.0609 G01 Z-0.1515? F120.0 X1.1529 Y-0.0778 X0.9299 Y-0.0944 X0.7066 Y-0.1074 X0.4832 Y-0.1169 X0.2596 Y-0.1227 X0.1105 Y-0.1246 X-0.1106 X-0.3484 Y-0.1208 X-0.5861 Y-0.1130 X-0.8236 Y-0.1011 X-1.0609 Y-0.0851 X-1.2979 Y-0.0651 X-1.5346 Y-0.0410 X-1.7707 Y-0.0129 X-2.0064 Y0.0192 X-2.2415 Y0.0553 G17 G02X-7.7519Y4.4694I0.9620J6.8475 X-7.4781Y9.3650I5.8485J2.1283 X-6.1583Y11.1056I6.2570J-3.3735 G01 X-5.9731 Y11.2914 G03X-5.4021Y11.9392I-5.5788J5.4928
chuck All Messages By This Member #154842 开云体育 Steve, its under config/general config? second column over like 3 boxes down. I J mode absolute or incremental. whichever is checked switch it. Chuck On 4/6/2021 6:31 PM, Stephen Muscato via groups.io wrote: toggle quoted message Show quoted text Could it be here? ????Ports & Pins ????Turn Options ??? "Reversed Arcs in Front Post"? is it checked?? I had a problem a long time ago and I may have unchecked this box to fix it. Steve On Tuesday, April 6, 2021, 3:59:29 PM CDT, chuck via groups.io <chuckels@...> wrote: Steve, been a while since I ran mach3 but there is a setting that has to do with I J K moves if I remember its a check box in one of the settings page. Chuck On 4/4/2021 10:06 AM, Steven DAntonio wrote: I just upgraded to R3.043.066 (from R2), I'm getting an error that says "radius at end of arc differs from radius to start, block =G02..." I downloaded the more recent R3 from Artsoft and the? fix log shows nothing after R3.043.62.? I can go back to R2 if need be, but I'm hoping I don't have to. This code runs under R2.? Code generator was RhinoCAM 2017.? I'm running under win XP SP 3 since my computers with an LPT1 port with not support anything higher. I'm seeing this error with every piece of code I have tested so far, all of which ran under R2 without issues. Here is a snippet of the code (bold line is the one that crashes) G00 G49 G40.1 G17 G80 G50 G90 G20 (Setup 1) (Work Zero) (2 1/2 Axis Profiling) M6 T2 M03 S20000 G00 Z1.0466 X1.3373 Y-0.0609 G01 Z-0.1515? F120.0 X1.1529 Y-0.0778 X0.9299 Y-0.0944 X0.7066 Y-0.1074 X0.4832 Y-0.1169 X0.2596 Y-0.1227 X0.1105 Y-0.1246 X-0.1106 X-0.3484 Y-0.1208 X-0.5861 Y-0.1130 X-0.8236 Y-0.1011 X-1.0609 Y-0.0851 X-1.2979 Y-0.0651 X-1.5346 Y-0.0410 X-1.7707 Y-0.0129 X-2.0064 Y0.0192 X-2.2415 Y0.0553 G17 G02X-7.7519Y4.4694I0.9620J6.8475 X-7.4781Y9.3650I5.8485J2.1283 X-6.1583Y11.1056I6.2570J-3.3735 G01 X-5.9731 Y11.2914 G03X-5.4021Y11.9392I-5.5788J5.4928
chuck All Messages By This Member #154843 开云体育 also G90.1 or G91.1 switches it if you have it in your code. On 4/6/2021 6:31 PM, Stephen Muscato via groups.io wrote: toggle quoted message Show quoted text Could it be here? ????Ports & Pins ????Turn Options ??? "Reversed Arcs in Front Post"? is it checked?? I had a problem a long time ago and I may have unchecked this box to fix it. Steve On Tuesday, April 6, 2021, 3:59:29 PM CDT, chuck via groups.io <chuckels@...> wrote: Steve, been a while since I ran mach3 but there is a setting that has to do with I J K moves if I remember its a check box in one of the settings page. Chuck On 4/4/2021 10:06 AM, Steven DAntonio wrote: I just upgraded to R3.043.066 (from R2), I'm getting an error that says "radius at end of arc differs from radius to start, block =G02..." I downloaded the more recent R3 from Artsoft and the? fix log shows nothing after R3.043.62.? I can go back to R2 if need be, but I'm hoping I don't have to. This code runs under R2.? Code generator was RhinoCAM 2017.? I'm running under win XP SP 3 since my computers with an LPT1 port with not support anything higher. I'm seeing this error with every piece of code I have tested so far, all of which ran under R2 without issues. Here is a snippet of the code (bold line is the one that crashes) G00 G49 G40.1 G17 G80 G50 G90 G20 (Setup 1) (Work Zero) (2 1/2 Axis Profiling) M6 T2 M03 S20000 G00 Z1.0466 X1.3373 Y-0.0609 G01 Z-0.1515? F120.0 X1.1529 Y-0.0778 X0.9299 Y-0.0944 X0.7066 Y-0.1074 X0.4832 Y-0.1169 X0.2596 Y-0.1227 X0.1105 Y-0.1246 X-0.1106 X-0.3484 Y-0.1208 X-0.5861 Y-0.1130 X-0.8236 Y-0.1011 X-1.0609 Y-0.0851 X-1.2979 Y-0.0651 X-1.5346 Y-0.0410 X-1.7707 Y-0.0129 X-2.0064 Y0.0192 X-2.2415 Y0.0553 G17 G02X-7.7519Y4.4694I0.9620J6.8475 X-7.4781Y9.3650I5.8485J2.1283 X-6.1583Y11.1056I6.2570J-3.3735 G01 X-5.9731 Y11.2914 G03X-5.4021Y11.9392I-5.5788J5.4928
Steven DAntonio All Messages By This Member #154844 Thank you all, it switched as soon as I? loaded up my xml profile.? Evidently this is something I must have struggled with about 10 years ago when I made up the original profile and had completely forgotten about.

Previous Topic Next Topic