开云体育

Mach3 One stepper motor won't move

David Hunkele All Messages By This Member #153859 I am replacing my computer on my plasma table. I loaded Mach3 on the new computer set it up with the same setting as the old one. Everything works as it should except one of my motors on the Y axis won't move. I plug in the old computer works fine. HELP!
o1bigtenor All Messages By This Member #153860 On Thu, Nov 21, 2019 at 8:18 PM <dhunkele62@...> wrote: I am replacing my computer on my plasma table. I loaded Mach3 on the new computer set it up with the same setting as the old one. Everything works as it should except one of my motors on the Y axis won't move. I plug in the old computer works fine. HELP! Have you checked for any diagnostics on said stepper motor? Done them? Results? Regards
David Hunkele All Messages By This Member #153861 Everything on the Mach3 diagnostics screen looks good as far as I can see. I know everything is good on the machine is good it works on the old computer.
[email protected] #153862 are you using the same breakout board or interface? have you compared the motor setting from the old and new computer? could you have wrong pin assignments on the new computer? check every setting. something is wrong. check signal polarities etc etc.? ? ? Best regards, Spencer Chase 67550 Bell Springs Rd. Garberville, CA 95542 Postal service only. Laytonville, CA 95454 UPS only. Spencer@... Spencer@... Spencer@... http://www.spencerserolls.com http://www.poodlex.com (425) 791-0309 (707) 223-8212 toggle quoted message Show quoted text ------ Original Message ------ From: dhunkele62@... To: [email protected] Sent: 11/21/2019 6:37:28 PM Subject: Re: [MachCNC] Mach3 One stepper motor won't move Everything on the Mach3 diagnostics screen looks good as far as I can see. I know everything is good on the machine is good it works on the old computer.
Les Cullen #153863 开云体育 I have an Industrial CNC 5x 12 with light use for sale. Contact at ins1234567@... toggle quoted message Show quoted text On Nov 21, 2019, at 7:18 PM, dhunkele62@... wrote: ?I am replacing my computer on my plasma table. I loaded Mach3 on the new computer set it up with the same setting as the old one. Everything works as it should except one of my motors on the Y axis won't move. I plug in the old computer works fine. HELP!
Dan Mauch All Messages By This Member #153864 You said one of your Y axis motors doesn't run. Did you check that slavingis setup in the config file? Dan
Ketan Patel All Messages By This Member #155280 On Friday, 22 November, 2019, 08:14:43 am IST, spencer@... <spencer@...> wrote: are you using the same breakout board or interface? have you compared the motor setting from the old and new computer? could you have wrong pin assignments on the new computer? check every setting. something is wrong. check signal polarities etc etc.? ? ? Best regards, Spencer Chase 67550 Bell Springs Rd. Garberville, CA 95542 Postal service only. Laytonville, CA 95454 UPS only. Spencer@... Spencer@... Spencer@... http://www.spencerserolls.com http://www.poodlex.com (425) 791-0309 (707) 223-8212 toggle quoted message Show quoted text ------ Original Message ------ From: dhunkele62@... To: [email protected] Sent: 11/21/2019 6:37:28 PM Subject: Re: [MachCNC] Mach3 One stepper motor won't move Everything on the Mach3 diagnostics screen looks good as far as I can see. I know everything is good on the machine is good it works on the old computer.

Previous Topic Next Topic