开云体育

Joggin' my noggin'

SCMWCAD1 All Messages By This Member #154969 开云体育 Hi Guys, ? Long time since I’ve been here. I’m using my Mach 3 controlled mills after a couple of years hiatus. I’m trying to remember how to move an axis by .001 when using a zero finder to the side of a piece of stock on the X or Y axis. I’m able to run programs and move the table around using the direction buttons on the keyboard but cannot for the life in me remember how to get mach to allow me to move in incredibly small increments. ? Anyone know what I’m talking about and how to do it? ? Thanks a ton, ? Terry Wellman ? Sent from for Windows ?
John Dammeyer All Messages By This Member #154970 开云体育 Hit the tab button to get the pendant out on the RHS. ?Set the amount to move in the jog increment. John ? ? toggle quoted message Show quoted text From: MachCNC@groups.io [mailto:MachCNC@groups.io] On Behalf Of SCMWCAD1 Sent: August-25-21 3:41 PM To: MachCNC@groups.io Notification Subject: [MachCNC] Joggin' my noggin' ? Hi Guys, ? Long time since I’ve been here. I’m using my Mach 3 controlled mills after a couple of years hiatus. I’m trying to remember how to move an axis by .001 when using a zero finder to the side of a piece of stock on the X or Y axis. I’m able to run programs and move the table around using the direction buttons on the keyboard but cannot for the life in me remember how to get mach to allow me to move in incredibly small increments. ? Anyone know what I’m talking about and how to do it? ? Thanks a ton, ? Terry Wellman ? Sent from for Windows ?
John Dammeyer All Messages By This Member #154971 From: MachCNC@groups.io [mailto:MachCNC@groups.io] On Behalf Of SCMWCAD1 Sent: August-25-21 3:41 PM To: MachCNC@groups.io Notification Subject: [MachCNC] Joggin' my noggin' ? Hi Guys, ? Long time since I’ve been here. I’m using my Mach 3 controlled mills after a couple of years hiatus. I’m trying to remember how to move an axis by .001 when using a zero finder to the side of a piece of stock on the X or Y axis. I’m able to run programs and move the table around using the direction buttons on the keyboard but cannot for the life in me remember how to get mach to allow me to move in incredibly small increments. ? Anyone know what I’m talking about and how to do it? ? Thanks a ton, ? Terry Wellman ? Sent from for Windows ?
SCMWCAD1 All Messages By This Member #154972 开云体育 Thank You John! That’s exactly what I was trying to remember. OK, now to go cut some swarf. ? Best, ? Terry ? ? Sent from for Windows ? toggle quoted message Show quoted text From: John Dammeyer Sent: Wednesday, August 25, 2021 5:52 PM To: MachCNC@groups.io Subject: Re: [MachCNC] Joggin' my noggin' ? Hit the tab button to get the pendant out on the RHS.? Set the amount to move in the jog increment. John ? ? From: MachCNC@groups.io [mailto:MachCNC@groups.io] On Behalf Of SCMWCAD1 Sent: August-25-21 3:41 PM To: MachCNC@groups.io Notification Subject: [MachCNC] Joggin' my noggin' ? Hi Guys, ? Long time since I’ve been here. I’m using my Mach 3 controlled mills after a couple of years hiatus. I’m trying to remember how to move an axis by .001 when using a zero finder to the side of a piece of stock on the X or Y axis. I’m able to run programs and move the table around using the direction buttons on the keyboard but cannot for the life in me remember how to get mach to allow me to move in incredibly small increments. ? Anyone know what I’m talking about and how to do it? ? Thanks a ton, ? Terry Wellman ? Sent from for Windows ? ? 109ED34C48284D52B857F334BFDFF8B0.png
John Dammeyer All Messages By This Member #154973 开云体育 I tried to post a screen shot too but it wasn't included.? Sorry about the wasted bandwidth on that. ? toggle quoted message Show quoted text From: MachCNC@groups.io [mailto:MachCNC@groups.io] On Behalf Of SCMWCAD1 Sent: August-25-21 4:05 PM To: MachCNC@groups.io Subject: Re: [MachCNC] Joggin' my noggin' ? Thank You John! That’s exactly what I was trying to remember. OK, now to go cut some swarf. ? Best, ? Terry ? ? Sent from for Windows ? From: John Dammeyer Sent: Wednesday, August 25, 2021 5:52 PM To: MachCNC@groups.io Subject: Re: [MachCNC] Joggin' my noggin' ? Hit the tab button to get the pendant out on the RHS.? Set the amount to move in the jog increment. John ? ? From: MachCNC@groups.io [mailto:MachCNC@groups.io] On Behalf Of SCMWCAD1 Sent: August-25-21 3:41 PM To: MachCNC@groups.io Notification Subject: [MachCNC] Joggin' my noggin' ? Hi Guys, ? Long time since I’ve been here. I’m using my Mach 3 controlled mills after a couple of years hiatus. I’m trying to remember how to move an axis by .001 when using a zero finder to the side of a piece of stock on the X or Y axis. I’m able to run programs and move the table around using the direction buttons on the keyboard but cannot for the life in me remember how to get mach to allow me to move in incredibly small increments. ? Anyone know what I’m talking about and how to do it? ? Thanks a ton, ? Terry Wellman ? Sent from for Windows ? ?

Previous Topic Next Topic