it works. i do have to say that plain text is not conventionally
used as an indicator of a button or clickable link or any active
screen component. there are all sorts of ways of calling attention
to an active component or link? using plain text is just plain
wrong. below is what you said that had me confused suggesting that
i should be able to find a button icon of some sort etc. when you
said that you have to click on the Motor)? text that made it
clear.
but you also have to click on the
Motor0, or whatever,
On 3/27/2021 12:25 PM, Steve Stallings
wrote:
One more time ----- on
the Motors tab of the Configure Control panel you will see a
list of motors on the right side.
?
You must click on the
Motor0 text, not the check box, so that it highlights with a
blue background. Then you will be able to edit parameters.
?
?
At this point I have just one problem. I want to prove that
mach4 will work for me and maybe take the transition slowly
since i have a few customizations that i really like.
When I try configure control motor all the entry boxes are
greyed out but i must have pins right and checked boxes to use
the axis because they move when i run a gcode.
i am going to look one more time for something that might not
be checked
if you have any places to look in mach4 config or ESS config or
any place out that might be responsible for the motor setting
page to not think there are motors? again they move under
program control.
On 3/27/2021 6:49 AM, Brian Barker
wrote:
Spencer,
I need to be at my desk for a bit later today and I am more
than happy to go over this with you.and get it setup. I know
you have been doing this for a long time and I know you
shouldn't have any trouble. I would like to know if we can do
anything to make it better.
Thanks
Brian
______________________________
Brian Barker
Engineering / Devlopment
ArtSoft | Newfangled Solutions
Livermore Falls, Maine (USA)
Phone: 207(618)1449
Webpage:
Yes i downloaded and printed the 51 pages did not
see anything about hotkeys but the youtube looks
promising.Maybe i missed another doc. Can not do many youtubes
at high res with our viasat rip off. Still need to know why
motor settings csn not be entered
On March 26, 2021 7:24:03 PM PDT,
Andy Wander
<ohawiseguyeh@...>
wrote:
Spencer:
Did you check out the docs about setting up Mach4 at warp9td site?
-----Original Message-----
From: [email protected] <[email protected]> On Behalf Of spencer@...
Sent: Friday, March 26, 2021 9:29 PM
To: [email protected]
Subject: [MachCNC] mach 4 and ess
I spent hours trying to get mach4 to work with ess. Boy is the configuration a confusing mess.
two things i just can't get to work but i am sure there will be others once i test my lube control and other things.
i think i can live without my customizations at least for a while but i just wanted to see if mach4 is really any better and worth the effort.
I CAN NOT GET MOTOR TUNING TO WORK. i have all pins assigned etc and i can run a test gcode but the steps are totally wrong and need to be changed. in the appropriate place (something like config control motors) i have the familiar motor tuning screen similar to mach3. however the steps speed and accel are greyed out and i can not enter anything. by default all motor checkboxes were checked and i unchecked and checked until i was exhausted. nothing i could do would let me enter the values.
also i can not find anywhere where hotkeys are assigned. i found a tutorial you tube by a woman who sounds very authoritative so i think i might have found the answer but i have viasat internet and videos are blurry pixels at anything other than high res which means i have to wait weeks for vids to load. this is why i seriously shy away from youtube.
we are in the list for starlink and hope to get it soon so we will be in the 20th or is that 21st century like everyone else.
with all the fabulous improvements WTF can't there be a downloadable pdf worth shit? i have a great manual for mach3 and did not have many problems installing or using it other than a few here and there and the bugs which have prompted me to try mach4.
so maybe hotkeys and other kule keyboard stuff will be explained buy the very confident sounding woman if i live long enough to download the high res video
however trying to find out why motor tuning is greyed out could take me into the next century trying to find the answer.
--
Best regards, Spencer Chase
67550 Bell Springs Rd.
Garberville, CA 95542 Postal service only.
Laytonville, CA 95454 UPS only.
Spencer@...
(425) 791-0309
开云体育 Links: You receive all messages sent to this group.
View/Reply Online (#154704): /g/MachCNC/message/154704
Mute This Topic: /mt/81644130/2320152
Group Owner: [email protected]
Unsubscribe: /g/MachCNC/leave/4768858/2320152/348162135/xyzzy [spencer@...]
--
Sent from my Android device with K-9 Mail. Please excuse my
brevity.
--
Best regards, Spencer Chase
67550 Bell Springs Rd.
Garberville, CA 95542 Postal service only.
Laytonville, CA 95454 UPS only.
Spencer@...
(425) 791-0309
--
Best regards, Spencer Chase
67550 Bell Springs Rd.
Garberville, CA 95542 Postal service only.
Laytonville, CA 95454 UPS only.
Spencer@...
(425) 791-0309
