开云体育

Thanks! Sent: Wednesday, September 4, 2019 4:03 PM To: [email protected] Subject: Re: [Losmandy_users_io] Two Questions About Gemini-2 Hi Mark great questions 1. yes it should save the time.

Hi Mark great questions 1. yes it should save the time. not sure why that's happening to you, make sure you save the values and you do not have any settings on your computer to overwrite these values

Hi, I've search high and low, and cannot find answers to these two questions. 1. My Gemini-2 hand controller does not save the time, nor does it get the time from the GPS (although it does take the

Wrote this up today elsewhere: . There were some differences in how folks numbered the pins of the RJ-12 modular jack. Probably why they flipped the connections. I know Meade PCBs start with pin 1 on

Thanks Mark. I thought I remembered seeing comments about grounding concerns with 492 drive as well, but IIRC that was for the "no relay box" scenario. Will try it out next non-cloudy night. If the

Tom, You didn't mention what your guiding exposure is. If less than 2 or 3 seconds then, yes indeed, you will be chasing seeing. You also didn't mention if you find the resulting images acceptable or

All: I mounted my meter-long Mak-Newt OTA on my GM811G, and while it doesn't hit the HD tripod leg as I slew, it comes perilously close (and did hit a dew heater control I had attached with a Velcro

Hello Tom Not too sure what guiding software you use, but bad seeing drives guiding nuts... If you use phd2 use guiding assist and run it for 3 or 4 minutes and it will make suggestions for you. After

Hi All, I'm hoping I might be able to reset my troubled brain when it comes to the guiding results I am getting from my backyard. To set the stage, I have a 12 month old G11 which I'm using with a

In PhD2 click on the Tools tab. The first item is Manual Guide. If you set the Guide/Slew rate in the 492 panel to 16X you'll be able to see and hear the manual guide corrections. I use the Manual

Thanks John. I’m constantly removing/re-installing my motors and we’re wondering if the threads would hold out. ?It appears no matter how careful you are you will wear the threads. -- Brendan

Joe, Brendan - thank you both very much. I'll give it a try next time the sky clears - if PHD2 includes manual slew controls I may not even have to wait that long - and report back. Thanks, John

I don't have a 492 but I repair Gemini 1 & 2's, Cameras.....and everything Astro put in front of me..... All modern ST4 outputs are either opto-coupled out or transistor TTL "low" signals.??

Yup I use a asi 120mc for guiding with my 492 using PHD2. Best move since st4 camera. Sent from my iDork

Hi all, I have a ~18 year old G11 with 492 drive. Used to guide it with an ST-237 + relay box, but (a) the relay box disappeared at some point and (b) I no longer have a computer old enough to run the

Recently, I found that the servo motor on my GM811G declination head was loose - that I can move it by hand against its gearbox.? Then I found?that I couldn't tighten the motor's 4-40 cap head

Welcome aboard Rick G11 is a great mount, and there’s lots of great people here to answer any questions you may have Thanks Brian portfolio https://www.brianvalentephotography.com/ Sent: Friday,

All, Joined this group a while back when I was trying to decide on my next mount. You’ve helped me decide on getting a G11. I have started ordering it “in reverse”. Getting all the small stuff

Thanks. Yes, I think I just need to start anew and tweak some things. 9 times out of 10, at least in my case, it turns out to be "operator error". Jim [email protected]> wrote:

Jim, After installing a new battery you must do a Cold Start from the Hand Controller. The make sure time and location are correct. You may need to redo your pointing model. Just went through this