CW Crystal Filters, 10 meter Crystals,
Knob, Amp Cables, Computer Interface,
TS-440 Parts, and more For Sale:
.
InRad CW Filters:
Both of these CW filters are 400 Hz wide,
striking a good middle ground between 500
or 600 Hz filters, and 250 Hz filters.
In addition to CW, these can also be used
for narrow digital work.
These are InRad filters, which most people
consider superior to other filters.
These were both used in a Kenwood TS-940,
although I am fairly certain that they can
be used in most other Kenwood rigs, and
probably some non-Kenwood rigs as well.
Both work fine, and look great as well.
InRad 455 H 400
This one is used in the 455 KHz IF, and of
course is 400 Hz wide. $125
InRad 88 H 400
This one is used on the 8800 KHz IF, and is
400 Hz wide as well. $100
Buy both for $215.
.
Crystals:
I have a set of three crystals that are used to
return the Kenwood Hybrid rigs to 10 meters,
after they have had the original crystals changed
to 11 meters.
Specifically, they are HC-25 crystals for 33.50,
34.00, and 34.50 MHz. They are labeled as
being for the TS-820, but I think all of the
hybrids use the same frequencies.
These crystals are $35 for the set of three.
.
Kenwood Heavy Duty Weighted Tuning Knob:
This knob is a special tuning knob, about 2 1/4
inches in diameter, so just right for most Kenwood
rigs. It is weighted, so one can give it a spin,
and it continues to go.
This one looks perfect, and is still in its
plastic bag.
Only $80.
.
Linear Amp Switching Cables for Kenwood Rigs:
This cable goes from a Kenwood transceiver to a linear
amplifier to switch the amp from transmit to receive.
One end has a DIN connector, as is used with most Kenwood
rigs. The other end has an RCA phono plug, as used by most
linear amplifiers.
Before using this cable, please check the switching
capabilities of your transceiver, and the requirements
of your amplifier.
Cable for switching the T/R relay Only $15.
Cable as above, but with ALC line in addition to
T/R switching. $20
.
Kenwood IC-10 computer interface
The Kenwood IC-10 is a "Kit" of two ICs plus
very, very extensive paper work. The ICs plug
into sockets to give you an interface to your
computer. Check your manual to see if this is
used with your rig.
This one appears to be new.
Only $15.
.
Kenwood Charger for TH-225 HT; $10
.
BNC Rubber Duck Antenna
Original from Kenwood TH-215,
about 5 inches long $10
.
I have parts for a Kenwood TS-440 available.
Hopefully we can keep a couple units working
and looking nice using these parts.
The complete "back end" is available. This includes
the finals and associated PC boards, the large
heat sink, the power connector, and other parts
on the back of the rig.
Both parts of the bottom cover are presently
available.
They look very nice, and might improve the
looks of your rig.
A complete set of knobs is available; they
look very nice.
The small little silver rectangular buttons
are still available.
The complete final module and heat sink assembly
is available.
Other internal PC boards are available
as well.
Most small PC boards, such as squelch/notch/mic,
selectivity switch, mic jack, front panel push
buttons, etc. are available. The volume control
and RF Gain control are both gone.
The automatic antenna tuner is NOT available.
Please let me know what you need.
.
I also have many other accessories available such as many
different types of microphones, HTs, VHF and UHF rigs, HF
and VHF/UHF antennas, connectors, miscellaneous accessories,
etc.
Just too many to list here. Please e-mail your requests.
.
Prices do not include shipping from Florida.
Thanks.
73,
Ken, W8EK
Ken Simpson
E-mail to W8EK@... or W8EK@...
Voice Phone (352) 732-8400
.
.
