10 meter Crystals, Hand Microphone,
Knob, Amp Cables, Computer Interface,
TS-440 Parts, and more For Sale:
.
Crystals:
I have a set of three crystals that are used to
return the Kenwood Hybrid rigs to 10 meters,
after they have had the original crystals changed
to 11 meters.
Specifically, they are HC-25 crystals for 33.50,
34.00, and 34.50 MHz. They are labeled as
being for the TS-820, but I think all of the
hybrids use the same frequencies.
These crystals are $35 for the set of three.
.
Hand Microphone with round 8 pin plug:
This hand mic works great on most Kenwood
rigs with the round 8 pin connector, such as
the TS-440, TM-241, TM-2530, TW-4000, and
others, including Alinco and ADI. It says
"Electret Condenser Mic" on the back.
Basically, this mic functions like an MC-43, with
a couple more features. It has the mic and PTT
switch; it also has up/down switches on the top.
There are four "extra" buttons labeled Call,
VFO, MR, and PF. What these four buttons do
depends on the rig. There is also a "Lock"
switch on the back.
Regardless if you use the four extra buttons or
not, you still have a mic that works like an MC-43.
-
This mic works fine, and looks like new.
It probably came with a rig, and was immediately
put in the drawer, and never used.
Only $30
.
Kenwood Heavy Duty Weighted Tuning Knob:
This knob is a special tuning knob, about 2 1/4
inches in diameter, so just right for most Kenwood
rigs. It is weighted, so one can give it a spin,
and it continues to go.
This one looks perfect, and is still in its
plastic bag.
Only $80.
.
Linear Amp Switching Cables for Kenwood Rigs:
This cable goes from a Kenwood transceiver to a linear
amplifier to switch the amp from transmit to receive.
One end has a DIN connector, as is used with most Kenwood
rigs. The other end has an RCA phono plug, as used by most
linear amplifiers.
Before using this cable, please check the switching
capabilities of your transceiver, and the requirements
of your amplifier.
Cable for switching the T/R relay Only $15.
Cable as above, but with ALC line in addition to
T/R switching. $20
.
Kenwood IC-10 computer interface
The Kenwood IC-10 is a "Kit" of two ICs plus
very, very extensive paper work. The ICs plug
into sockets to give you an interface to your
computer. Check your manual to see if this is
used with your rig.
This one appears to be new.
Only $15.
.
Kenwood Charger for TH-225 HT; $10
.
I have parts for a Kenwood TS-440 available.
Hopefully we can keep a couple units working
and looking nice using these parts.
The complete "back end" is available. This includes
the finals and associated PC boards, the large
heat sink, the power connector, and other parts
on the back of the rig.
Both parts of the bottom cover are presently
available.
They look very nice, and might improve the
looks of your rig.
A complete set of knobs is available; they
look very nice.
The small little silver rectangular buttons
are still available.
The complete final module and heat sink assembly
is available.
Other internal PC boards are available
as well.
Most small PC boards, such as squelch/notch/mic,
selectivity switch, mic jack, front panel push
buttons, etc. are available. The volume control
and RF Gain control are both gone.
The automatic antenna tuner is NOT available.
Please let me know what you need.
.
I also have many other accessories available such as many
different types of microphones, HTs, VHF and UHF rigs, HF
and VHF/UHF antennas, connectors, miscellaneous accessories,
etc.
Just too many to list here. Please e-mail your requests.
.
Prices do not include shipping from Florida.
Thanks.
73,
Ken, W8EK
Ken Simpson
E-mail to W8EK@... or W8EK@...
Voice Phone (352) 732-8400
.
.
