开云体育

Yea i set a few different resolutions and they dont affect the program features, just the entire resolution, which, size wise, im fine with. Ill re-go over the higher res' again just to triple check

I’ve never had any luck with any Chinese radios using VOX and anything packet, although the UV-5R and md380 are the only ones I’ve tried. I ended up using my tnc-x TNC and creating my own cable.

Hey all, I followed Jason's "Pi Zero Project" videos to build a Pi Zero headless setup. A great help for a newcomer to digital modes! No problems with initial install of AX.25 or Pat. All command

Hi folks, I'm having an issue with the Red Cross custom forms with in FLMSG.? You open them with the "Edit Form" button.? It opens the form in the browser opens, but after a few seconds it crashes

I'm struggling to get audio for my IC-705 and JS8Call on RaspberryPI (Bullseye) working. CAT control works fine (button turns green). The dropdowns for "Modulation Soundcard" in Settings are empty /

Have you set a higher resolution for VNC desktop in the pi configuration?

I recalled that I had a Signalink so I ordered a cable. I will report back here to confirm the PTT works. I looked at the Digirig and it looks good. I plan to purchase that for another APRS system.

the same here. I run a raspi 4B also in an ARGON40 with with BAP on Bullseye. The distance argon40 to the router is only 1m, but I loose again and again wifi connection. This maybe after several hours

Kevin, The same RPI4 in the same chassis did the BAP build with a WiFi connection.? Hours of downloads. Never has a significant problem with the WiFi on this machine when running BAP builds on Buster

For Comparison, I put 32bit Bullseye on the card, updated, then did a full install of BAP Everything installed on the first attempt, including FLDIGI So there is something a little different with the

I was hoping anyone could help me out a bit. Im getting portable digital operations ready and, in such, i have a pi 3b+ with js8call on it. The program loads up fine and seems ready to test; but, the

I have an ArgonOne V2 case. I love mine, but they do have an issue with reducing WiFi signal strength (google it). I have one set on it's side (it's headless anyway) with the bottom pointing in the

Did a full build w newest version of BAP on an RPI4 mounted in an ARGON40 enclosure with a 256gb SSD.? Everything went as well as one can hope for.? System worked on SD.? System worked on SSD.?

Did a full install with the newest version of BAP.? Came up nicely.? Both monitors work.? GPS is a little slow to sync ... not a BAP problem.? Transferred the system to the SSDD of my Argon40 and

Every one of my attempted Bullseye upgrades has gone poorly. Every one that worked I started from a clean install. Mike KO4BCN

So yesterday I upgraded from Buster to Bullseye. I saved copies of important files and proceeded with the upgrade. When finished the menu items were different and BAP update was no longer there as

The baofeng cable you mention is TRRS. Is your sound card TRRS or TRS? If it is TRS, you may need an adapter to get this working. As a side note, you may find it very disappointing to use VOX on the

Here's the one I made. I started here: https://oh8stn.org/diy-battery-storage/ Julian has a LOT of great information on portable and off grid ops. The BMS is an APEX that I? got off Ebay

For 2M Winlink connections, you will need the following installed at a minimum: direwolf ax25 pat pat menu For HF ARDOP Winlink connections, you will also need: ARDOP ARDOP GUI All of the above can be

I've not played with using vox for this, but I have keyed a BaoFeng by wiring my connector lead to use GPIO5, and set? Direwolf to pull it low for PTT. 73 Phil 2E0HGU