开云体育

Hi, Eugine Have you updated the eeprom in order to boot from usb? Here is a detailed howto: https://www.tomshardware.com/how-to/boot-raspberry-pi-4-usb -- 73 Daff, LZ1DAF

Everything is running smoothly now, except my SSD boot that I am still unable to get starting on the USB 3. It previously worked with the hack and with the SD still in place (even before the new

Everything is running smoothly now, except my SSD boot that I am still unable to get starting. Im using the above Wifi dongle and purchased a original D-Link DUB-H7 hub with external 5V power (Not the

My RTS and DTR radio buttons is not on because its not connected with my homebrew cable, but it works Pardon for the late reply, was out of office -- 73 de Eugene / ZR4EM

Still can't boot up with SSD, something maybe wrong -- 73 de Eugene / ZR4EM

You can remove build a pi by removing the directory ~/pi-build This will not remove anything that you installed during the build. For that, you will need to flash a new card. -- 73, de KM4ACK YouTube

Is there a command I can run to completely remove build-a-pi, so that I can reinstall everything fresh.

Okay, I got it going. I am putting the settings for flrig below incase anyone else needs them. RTS + 12v and DTR + 12v needed to be on at the same time. @ZR4EM thank you for helping me figure this

I'm very new to this could you explain, "data flow, with one start bit, 8 data bits and two stop bits, no parity or flow control" what this looks like in the settings? I set to 4800 baud, and 2 stop

@ZR4EM I am running a Raspberry Pi 4/4gig with buster and the build-a-pi script. I have looked at the baund rate in the 890 manual it says 4800, but I cannot find the other settings you mentioned.

Jason solution worked well but I missed the colours used in Direwolf so I installed from the dev branch; cd ~ git clone https://www.github.com/wb2osz/direwolf cd direwolf git checkout dev mkdir build

Hi! I also have a problem with GPS when using a USB 3 device. My GPS module is a Quectel L83, connected to GPIO serial port and an extra pin for 1PPS signal. When my RPi4 boots via the SD card there

See this site ( https://elinux.org/RPi_VerifiedPeripherals#Powered_USB_Hubs ) regarding?Peripherals especially the power of the USB port, so it seems that the power drawn from the port more than

I see on the user manual of your rig its very similar to my FT-840. On p31 in the manual it explains the data flow, with one start bit, 8 data bits and two stop bits, no parity or flow control. I also

It may be advantageous also to use a lower port speed than the maximum rate of your devices. My experience is that 9600 is the better rate as my FT-897 was previously set on 38k and it worked fine on

Are U using a PC, MAC or Linux machine. I also have some issues with FLrig and Fldigi but its more related to the sound, but what I can tell you is that all the baud rates and Com port settings have

So my Yeasu FT-890 is connected using a CAT to USB-FTDI cord my Baund is set at 4800 when I click Init I get this error: Transceiver not responding! Check serial (COM) port connection Open menu

The problem, seems to me, may also be supply related as well as the Linux core. I'm not sure what anymore, Its just demoralizing to battle so much with a piece of hardware. My order of business after

Hi Craig I also got that problem early on especially because I'm running from a UBEC supply directly coupled to the GPIO port but it seems that that is sorted. I will certainly have a close watch on

Hi Jason, Did you check dmesg (diagnostic message)?log? That may give you some idea what is happening. From terminal just run dmesg (I prefer to add -T option to give the timestamp). There will be