ctrl + shift + ? :
Show all keyboard shortcuts
ctrl + g :
Navigate to a group
esc to dismiss
its a poor idea of allotment 14.105 is old packet new vara-ac and now also HF APRS sheesh!
additionally there is no more information 300 baud is normal for HF so just set dire wolf to 300b and dial on 14.105 ... and try and find some air space..?
|
sudo apt install python3-gps
This will install gpsd, gpsd-clients too as dependencies.
Kevin -- KD9EFV -- EM78dh
|
I see Flrig PTT on the radio.? If this was UZ7HO it has the ability to PTT. Dierwolf?I don't have a clue.?
Is there a way??My Mag loop could pull this in.?
73
Don Poaps
New Westminster, BC
VA7DGP DATA VA7QU ? VOICE Winlink:?va7dgp@...
Subject://wl2k ? ? ? ? ?
ALLSTAR ?530780
Hamshack Hotline5971
Mid-Island Phone Mesh 2210 2232
? ? ? ? ? ? ? ? ? ?
|
What is the command for installing gps on bullseye?
THank you,
Pat
|
The Pi Zero 2 W is essentially a RPi 3b + with half the RAM, no Ethernet connection, and fewer USB ports.
The Pi Zero 2 W is a quad-core board compared to the original Pi Zero W's single core.
| |
Ken, N2VIP
toggle quoted message
Show quoted text
On Sep 27, 2022, at 03:57, Vic WA4THR via groups.io <vhklein@...> wrote:
?When the RPi Zero 2 W came out, I immediately changed to it and it works MUCH better that the original zero. I have no problem running Fldigi or WSJT-X as it has a 1uad core processor that runs pretty much like a RPi-3, as I understand it. I did have an odd problem in that the newer RPi Zero 2 would shut down from overheating sometimes, but I replaced the plastic housing seen in an earlier post with an Flirc case that is the same size, but made as an aluminum heat sink, and that solved that problem. I routinely use the new setup in digital modes in portable or remote operations. I just got back from a family vacation for a week on the Outer Banks where I had my QRP rig and a KM4ACK 40m EFHW set up for early mornings and evenings and worked 28 countries from Australia to Greece on 10w, mostly digital modes (PSK-31 and FT8) using the setup. Note I don't use Flrig, just select the appropriate rig for control from the menu in either Fldigi or WSJT-X.
So what did I do with the original Pi-zero? I plugged it into an old cell charger and run Pi-Hole on it to strip pop-ups from all the devices on my home network.
=Vic=
fresh install of Build a pi on a compute module 4 when I try to run BPQ config Generator i get an error??/home/pi/linbpq/piBPQConfigGen: No such file or directory but the file is in that directory as you see below.?
~/linbpq $ ls -la
total 7420
drwxr-xr-x? 4 pi pi? ? 4096 Sep 27 16:08 .
drwxr-xr-x 27 pi pi? ? 4096 Sep 27 16:01 ..
-rw-r--r--? 1 pi pi? ? ?827 Sep 27 15:53 bpq32.cfg.bak
-rwxr-xr-x? 1 pi pi? 536128 Mar 21? 2022 bpqaprs
drwxr-xr-x? 3 pi pi? ? 4096 Dec 18? 2014 BPQAPRS
drwxr-xr-x? 2 pi pi? ? 4096 Sep 27 15:53 HTML
-rwxr-xr-x? 1 pi pi 4777216 Sep 22 18:13 linbpq
-rwxr-xr-x? 1 pi pi 2258988 Mar 28? 2021 piBPQConfigGen
any ideas?
?
|
To get vara on pi check this?
As for other issues, it sounds one off - just personally I have flashed a few devices with no issues as of recent with this script to speed up installs of ham softwares.?
to add some details you install the OS this project script just installs software quickly and automated on top of it. It¡¯s not modifying the OS for display or boot issues for example.?
|
Interesting program it¡¯s not installed with this scrip so you need to install it like you would elsewhere.
appears to have a full help for install?.?
as for your question about digital modes yes Fldigi and wsjt software is used check out this projects YouTube or GitHub
as for monitoring multiple modes simultaneously this is a limitation of your setup and such
|
Bullsey uses python3-gps
Buster may have had python-gps or python2-gps deprecated.
Kevin -- KD9EFV -- EM78dh
|
Thank you gents for responding, reading the T&C for winlink it seems they want dedicated hardware and goals to keep the gateway operating 24/7/365. I understand that they want a reliable infrastructure and I suspect my ¡°in an emergency¡± deployment would be in violation. Maybe one day I¡¯ll have resources to commit, but not right now.?
73 and I hope everyone in Ian¡¯s path stays safe!
Edward [KU3RRY]
|
On this BAP build I didnt install gps, gps tools and conky to try something different because I am trying to get my gps working, and I was unable to with the gps tools.? I tried to install gpsd gpsd manually but I got this when attempting?? This is what I used when setting up the gps on my other pi4 and my linux laptop. Am I unable to do it this way with BAP?
TIA,
Pat
|
On one of my my pi4's I have a software tnc ardop status that I click on before I use gARIM that let's me choose pauvcontrol and ardopc. Which software do I use for gARIM? Also will BAP allow me to monitor,? JS8, Fldigi, FSQ and gARIM at the same time?
TIA,
Pat
|
When the RPi Zero 2 W came out, I immediately changed to it and it works MUCH better that the original zero. I have no problem running Fldigi or WSJT-X as it has a 1uad core processor that runs pretty much like a RPi-3, as I understand it. I did have an odd problem in that the newer RPi Zero 2 would shut down from overheating sometimes, but I replaced the plastic housing seen in an earlier post with an Flirc case that is the same size, but made as an aluminum heat sink, and that solved that problem. I routinely use the new setup in digital modes in portable or remote operations. I just got back from a family vacation for a week on the Outer Banks where I had my QRP rig and a KM4ACK 40m EFHW set up for early mornings and evenings and worked 28 countries from Australia to Greece on 10w, mostly digital modes (PSK-31 and FT8) using the setup. Note I don't use Flrig, just select the appropriate rig for control from the menu in either Fldigi or WSJT-X.
So what did I do with the original Pi-zero? I plugged it into an old cell charger and run Pi-Hole on it to strip pop-ups from all the devices on my home network.
=Vic=
|
After testing BAP 2.10.0 on earlier release of Pi OS 64bit PAT(v0.13.1), ARDOP, and VARA-HF were working as expected.? I decided to do a fresh build. I am using a Pi 4b.? For the build I used a fresh Bullseye 64bit with update, released early in September.? I installed BAP 2.10.0 and PAT v0.13.1.? I also installed the software required for VARA.? VARA-HF is working fine.? When I tried to run ARDOP it failed.? The ardopGUI runs and is displayed but piardopc fails.? The piardopc window flashes and closes and fails to display activity. The version of piardopc used in the problem build is the same version that I used in an earlier Pi build that is running as expected.? The following is from?ARDOPDebug8515_20220927.log in the failing version.
01:55:53.989 ardopc Version 1.0.4.1mBPQ-Debug5
01:55:53.989 ARDOPC listening on port 8515
01:55:53.989 Capture Devices?
|
That did it! I neglected the ./ before update!
Now how do I get the update tool in the Hamradio/BAP drop-down menu?
On Monday, September 26, 2022, 8:44 PM, km4ack <jason.oleham@...> wrote: Let's forget the menu shortcut for a minute. Something isn't adding up. In the last screenshot you posted, the update script is clearly in the directory. Run this command and screenshot the output ~/pi-build/./update Note the "./" in front of update --
73, de KM4ACK
|
|
|
Wow...I'm outta ideas...back in Jason's court now....wish I could have helped.
Jerry
Unfortunately not. When trying to run update from the ~/pi-build I get:
bash: update: command not found.
Rich
|
Let's forget the menu shortcut for a minute. Something isn't adding up. In the last screenshot you posted, the update script is clearly in the directory. Run this command and screenshot the output ~/pi-build/./update Note the "./" in front of update --
73, de KM4ACK
|
|
|
Re: Didn't run pi-build from $HOME
I got it working. It turned out that when I switch the conky-size to "conky-7inch" that was causing the issue. I thought this might work since the display I am using is 7-inch. When I set it back to conky-small, the conky display came up. Hopefully I won't run into any other issues related to not putting pi-build in $HOME.
|
Unfortunately not. When trying to run update from the ~/pi-build I get:
bash: update: command not found.
Rich
|
|
|
Don Poaps
Alex (KD0YTE)
Vic WA4THR
km4ack