开云体育

Had this WiFi problem too. Found on internet this blog. https://www.martinrowan.co.uk/2021/01/argon-one-m-2-ssd-case-for-raspberry-pi-4-review/ Looks like a bug in the Argon design. I contacted Argon

If you are using bullseye, in preferences, under headless, there is screen size. The default is none. Choose your screen size on the pi that you want to vnc into. This ia a change fron buster. I

Hello Dave the user name should be just "pi" with a password of "raspberry"? unless to changed it when you VNC into where it asks for username and password there should be a box just below password

Hey Mike! Nice to catch you around again! Thanks for the heads up. I'll suggest changing the SSID. 73 de VE3GKT

Hi Jason, So, I am using a Yeasu FT-8800 for 2m and IC-7300 for HF. I can receive packet info on the APRS frequency on my 2m with pat http and direwolf running. For 2m, I open Direwolf and terminal

Chris ..... I have to get batteries for my chair as well ( there are two 55AH =) Which batteries did you use and do you use the battery charger that came with the chair ??? Thanks for your responce=)

Hello Joseph, I had an issue with my wifi when there was a space in the SSID. Seems like the Rpi wouldn't connect up. I do have other Rpi's at my house, but they are for non-ham things that don't use

GA all I don't have screencaps handy just now, but I can get them if needed. When I open Hotspot Tools and select "Managae SSIDs", I might have two networks saved, but there will be four lines. One of

Hey Terry, I don't know what size batteries you use in your chair. However I got rid of my 2 heavy as fun! And replaced with liposuction. My chair will actually travel about 3 miles further with less

I don’t have any experience doing this but I would think you could use a cheap SDR receiver dongle and software to look at the signal. You should be able to see how wide it is on the screen. Jeff

Yesterday I ordered a Digirig and Baofeng cable. I am running BAP What changes do I need to make to direwolf.conf to enable PTT in this configuration? thank you

Look at data over a scope. It must be pure sinewave then you know levels etc are 100%. Normaly at about 2.5khz deviation is good. Greetings from the Namib Pieter Jacobs +264811277615 NETS NTNSS

The only reason I posted was the price in Canadian dollars. There's a difference between Amazon.Com and Amazon.CA. 73 *Don PoapsNew Westminster, BC*VA7DGP DATA VA7QU VOICE *Winlink: va7qu@...

For 9600 Baud AX25, Yaesu recommends using a Deviation Meter to set the deviation. ?I get intermittent success with various sites and probably need to adjust my radio. Does anyone have an idea for an

Hey Don, I've picked up a couple of these on the US Amazon store:

Unless you changed the account name, it should be pi for username. Should also be your pi password. 73, KB5WCK ________________________________ Sent: Saturday, February 12, 2022 9:57:06 AM To:

I was able to ping the IP. I then was able to verify that VNC was enabled. Now I can’t remember what username and password combo to use when settiup the vnc connection. I should remember but this

Dave First I would recommend adding a blank text file - ssh.txt -? then using putty or what have you on windows or terminal on macs. ssh into the build a pi, run "sudo raspi-config" turn on? VNC

Another possible answer:? Sometimes when I boot my Pi it fails to recognize my Wifi so I have to wait until the Hospot timer tries again.? I set mine to 2 minutes.? Then it works as usual.? For

Most obvious question: Did you enable VNC in raspi-config, Interfaces, VNC? Kevin -- KD9EFV