开云体育

Hello I’m running BAP on a pi4 and I can not get it to transmit , I am running 991a with cat cable for ft8/js8call with no issues ? When I go to run Pat it will ?not transmit? Any suggestions?

I had rebooted multiple times and that did not solve it. Instead, I reloaded Bullseye and used your Build tool to install FLRig and JS8Call. It works now. I still want to understand how to use the

Hi Everyone, I'm looking for a bit of advice please. I can't see my RPi SSID on my iPhone or iPad and therefore be able to connect when using the hotspot in BAP. I can connect fine using my home wifi

I notice that when I click on JS8CALL to change frequency like 14.078 or any other JS8Call frequency. Something has locked it. Click on 20 M and it goes to 20 and bounces back to 7.078. Unable to QSY

It's working but just can not connect to VA7PF or the next closest Gulf Island USA Winlink Gateway. 73 *Don PoapsNew Westminster, BC*VA7DGP DATA VA7QU VOICE *Winlink: va7qu@...

I have a feeling that the USB plug got pulled or moved in my small usb hub. It's not showing up in *ls -l /dev/serial/by-id* *I have to go out and check shortly.* *73* *Don PoapsNew Westminster,

I must have something wrong. 2022/02/14 17:29:42 Unable to get frequency from rig my-rig: dial tcp 127.0.0.1:4532: connect: connection refused. 2022/02/14 17:29:42 Starting HTTP service

This is a full BAP load on a Pi 4.

Duh!! I didn't even noticed Rig Control. Changed to Yes. I'll turn on the Xiegu G 90 and see if my 40 m Hamstick can connect to Ardop gateway. I always needed some one to look over my shoulder to make

Anything that uses OpenVPN can be done fairly easily. Don't know anything about that one you mentioned.

Anyone try to make the Virtual Shield VPN work with BAP? Really would prefer not to open my network up to the internet without this sort of protection. Thank you

The kit ships with ~68' of wire. -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack ) Twitter ( https://twitter.com/km4ack ) | Store (

make sure the rig is on and then reboot the Pi and see if that clears the issue. I have ran into this issue occasionally before if I boot the Pi before turning on the radio. -- 73, de KM4ACK YouTube (

Did you set rig control to "on" in Pat Menu Settings? -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack ) Twitter ( https://twitter.com/km4ack ) | Store

Did you load Pat Menu with Build a Pi or is this a custom/manual build? -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack ) Twitter (

[image: 2022-02-14-155821_1920x1080_scrot.jpg] I had to use scrot to create a screen cap and use Pat Winlink to send it to my email address so you can see what the issues are. I have Digirig running

I get: **** List of CAPTURE Hardware Devices **** with nothing listed.

Thanks Jason! I’m going to become a Patreon of your channel today!

This is the info I was looking for. Getting Pat Winlink to PTT using my Xiegu G 90. I have no issues with JS8CALL etc. 73 *Don PoapsNew Westminster, BC*VA7DGP DATA VA7QU VOICE *Winlink:

After configuring the Pat Menu with appropriate card and device number from arecord -l, I can perform "reboot" numerous times and the card and device numbers remain constant, and Pat Winlink works