开云体育

I would think that you did make an error in winding. Mine was better then 1.5:1 on 40,20,15,10 AND 12 meters. 12 was a pleasant surprise. It’s a great kit and works perfectly with the SOTABEAMS

I am trying to set up WebRTC or similar to communicate voice (I have FT8, WSJTX, and JSCALL working) over IP.? I have a pi set up running for my IC 7300 that I would like to remotely key VOICE using

I think I have found the error in my winding. I will attempt a correction - if I can remove the hot glue ;-). For my information, about how long is the wire that comes with the kit? Thanks again for a

Your best bet is the check with the developer of FLMSG /g/linuxham/topics I haven't used FLMSG in a LONG time. -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (

It doesn't seem as though the Pi is "seeing" the sound card in the 705. What do you get if you run: *arecord -l * -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (

Have you seen the digirig sound card? It relatively inexpensive and works surprisingly well with a Baofeng. https://digirig.net/ -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (

I have no experience with the 8800 but PTT may be the issue. Which sound card are you using? If it's the Signalink, then the Signalink will handle the PTT for you as it has a built in VOX circuit. For

In the direwolf.conf file, you need to add this line to the PTT section (line ~184) PTT /dev/ttyUSB0 RTS -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (

You have a couple of issues going on here. Do you have FLRIG running? Build a Pi is designed to use FLRIG for rig control. Did you install ARDOP & the ARDOP GUI? -- 73, de KM4ACK YouTube (

I haven't started testing with the 64 bit OS yet but hope to get to it later this week. Currently Build a Pi only officially supports 32bit. -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) |

Can you post a pic of your toroid please? If the dip is at 6.8/6.9, the wire is still too long. Extra length is shipped with each kit to allow for minor mistakes. -- 73, de KM4ACK YouTube (

VARA isn't available for Pi OS yet. There are some guys trying to get it working with Pat so hopefully we will see that support added in the future. -- 73, de KM4ACK YouTube (

You can use Pat Menu & Pat winlink for Winlink emails. For APRS, you will need to look at an application like APRX. Direwolf won't work with the Mobilinkd. Direwolf is a software TNC and the Mobilinkd

Running PT on a Pi 3B+ ... and an IC705 (with address set to 94h to match 7300).? Pi on wlan to home network with VNC to access Pi screen. Everything looks good up to trying to connect.? Always get

My 80m EFHW is 134' with 49:1 unun and I get about 1:2 SWR. Mine followed a different plan and I use a nanovna to measure its SWR. I have good SWR on all ham bands except 160 and 6 meters. On Sun, Feb

I created a new 64bit Bullseye install last night and ran BAP (3.2.2), I installed WSJT-X, GridTracker and Hamclock. WSJT-x configured and running fine, when I try to run GridTracker from menu I get

Just build the KM4ACK EFHW today and threw it up in a tree, about 35 feet, sloping to ground. Put an SWR meter on it and found the lowest SWR I can get is 2.3 and that is at 6.8. I tried shortening

Will you be adding vara-fm to build-a-pi? Thanks

I too purchased it for HF.? Maybe if enough of us cash paying customers let the developer know that we would like it for Linux he might listen?

> I've got a yaesu ft2dr and a mobilinkd on the way. How would you think > it's best to integrate into a pi zero w build of this? Wanting to explore > direwolf and the rest of the aprs and winlink