开云体育

I ended up ditching the SignaLink and went to the Sabrent sound card - much better and easier. ?I'm getting tones out, and was connected for almost 90 seconds to a local EOC, but didn't get emails to

There's no need to be root so you shouldn't use "sudo bash" Make sure you are the pi user and run rm -rf ~/pi-build The above command will remove any previous downloads. Now run git clone

Did you enable VNC? From the main pi menu->preferences->raspberry pi configuration. Look under the interfaces tab. Is VNC set to enable? -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip

pi@house:~ $ sudo bashroot@house:/home/pi#? git clone https://github.com/km4ack/pi-build.git $HOME/pi-build && bash $HOME/pi-build/build-a-pifatal: destination path '/root/pi-build' already exists

It seems that there is some problem with the ftdi drivers and Linux -- 73 de Eugene / ZR4EM

@ KN4VXP Maybe its the port you are connecting to. Perhaps you should try another available port. Look for a similar description or try entering the command lsusb in terminal to see the port. It is

Well, maybe... I can run build-pi, but when I check flrig, it does not install. (it does install PAT... and RTC OK) I am also NOT getting VNC showing on the upper bar (top right). I can NOT check the

Nope it seems to be a USB hickup with the Linux core. So no, its maybe a collection of stuff and its frustrating. The other stuff is when the baud rate (not in your case) is fine for an instant but

The guys that build/maintain FLRIG might be able to give you specifics on the errors you are seeing. /g/linuxham/topics -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip

What error are you seeing? -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack ) Twitter ( https://twitter.com/km4ack ) | Store (

Not an answer as to why your Signalink doesn’t key the radio but the FT857 has data VOX built in that will get you up and running. * menu 40 Dig VOX 95

Has anyone a issue after they updated buster of the build a pi not wanting to install

Also, JS8CALL works perfect connects the first try every try. I don't get it?

I don't know if anyone can take a look at this error report from flrig and advise? I'm not sure what I'm looking at. I was able to connect to the radio all day yesterday and can't connect for anything

My setup: 1. BAP v2.0 2. Pi4 3. TS-590S on USB 2.0 4. U-Blox GPS on USB 2.0 5. Boot Device: SD Card I plugged in a spare CM108 based USB sound card directly into the back of the Pi's USB 3.0 and boom,

Dafcho's answer is the right one. After lots of trial and error testing, I came to the same conclusion. Video coming soon. -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (

I have a similar problem with a Kenwood D74 used as a KISS modem, If the D74 was on at boot up the GPS would fail. I eventually worked out that the D74 could boot up as ttyACM0, 1 or 2 and sometimes

This may be completely off beat but I too kept losing my GPS about 50% of boot ups but only when using my Kenwood D74 connected by USB so I could use it in KISS mode with Xastir. I also noticed that

It worked like a charm all day yesterday, got up this morning and it won't connect. Might be a hardware issue with the radio. I'm reinstalling Build-a-Pi now.

My setup: 1. BAP v2.0 2. Pi4 3. TS-590S on USB 2.0 4. U-Blox GPS on USB 2.0 I plugged in a CM108 sound directly into the back of the Pi's USB 3.0 and boom, the GPS is gone. Plug the sound card in with