Keyboard Shortcuts
Likes
- KM4ACK-Pi
- Messages
Search
Re: Heads-up for Canadian Miady battery
Chris ..... I have to get batteries for my chair as well ( there are two 55AH =)?? Which batteries did you use and do you use the battery charger that came with the chair ????? Thanks for your responce=)?? The chair really come in handy for Hamfest cruising :-))) On Sat, Feb 12, 2022 at 2:26 PM Chris Robinson KF6NFW DMR ID 3153250 <kf6nfw@...> wrote:
-- 73's Pat? N5VMO |
Re: Hotspot Tools issue with home SSID
Hello Joseph, I had an issue with my wifi when there was a space in the SSID. Seems like the Rpi wouldn't connect up. I do have other Rpi's at my house, but they are for non-ham things that don't use the Hotspot script. All was fixed when I changed?my SSID and removed spaces. 73's ? -- Mike WB8ERJ Geeze! What is he up to now? |
Hotspot Tools issue with home SSID
GA all
I don't have screencaps handy just now, but I can get them if needed. When I open Hotspot Tools and select "Managae SSIDs", I might have two networks saved, but there will be four lines. One of the networks has three words with spaces separating them, and each word appears as a separate line. Ideally, I'd like each network to appear as a separate line, no matter how many spaces are in one name. It's my dad's network so I can't just go ahead and rename it without spaces.? Has anyone noticed this before?? Thanks for everything you do for the hobby, Jason! I love the script and have been using it since V2. 73 de VE3GKT? |
Re: Heads-up for Canadian Miady battery
Hey Terry, I don't know what size batteries you use in your chair. However I got rid of my 2 heavy as fun! And replaced with liposuction. My chair will actually travel about 3 miles further with less weight. I then took two more of these lightweight batteries to make a radio pack with. I forget about them often on back of chair and have nearly caused a fire by crushing one of them when backed up out of way. After that, I don't leave attached to chair unless actively using it. The two Batts in chair were 12@55A, which make for great backup system in house with the yearly exchange on batteries. On Sat, Feb 12, 2022, 8:52 AM Don Poaps <va7dgp@...> wrote:
|
Re: Deviaton meter
¿ªÔÆÌåÓýI don¡¯t have any experience doing this but I would think you could use a cheap SDR receiver dongle and software to look at the signal.You should be able to see how wide it is on the screen. Jeff Townsend WB8LYJ
|
Re: Deviaton meter
¿ªÔÆÌåÓýLook at data over a scope. It must be pure sinewave then you know levels etc are 100%. Normaly at about 2.5khz deviation is good.?Greetings from the Namib Pieter Jacobs +264811277615 NETS NTNSS nets@... On 12 Feb 2022, at 18:51, Don via groups.io <Ddodge40@...> wrote:
|
Re: Heads-up for Canadian Miady battery
The only reason I posted was the price in Canadian dollars.? There's a difference between Amazon.Com and Amazon.CA. 73 Don Poaps New Westminster, BC VA7DGP DATA VA7QU ? VOICE Winlink: va7qu@... Subject://wl2k ? ? ? ? ? ALLSTAR ?530780 Hamshack Hotline 5971 Mid-Island Phone Mesh 2210 2232 ? ? ? ? ? ? ? ? ? ? On Sat, Feb 12, 2022 at 8:46 AM WA4TUX Dave <wa4tux@...> wrote:
|
¿ªÔÆÌåÓý
Unless you changed the account name, it should be pi for username. ?Should also be your pi password.?
73,
KB5WCK
From: [email protected] <[email protected]> on behalf of David Poulson via groups.io <kb7byi@...>
Sent: Saturday, February 12, 2022 9:57:06 AM To: [email protected] <[email protected]> Subject: Re: [KM4ACK-Pi] Created a Build a Pi SD card last night. Now I can't VNC into it today #bullseye #direwolf #conky ?
I was able to ping the IP. I then was able to verify that VNC was enabled. Now I can¡¯t remember what username and password combo to use when settiup the vnc connection. I should remember but this one brain doesn¡¯t retain like it use to. I thought is was pi-star then password. Nope. Tried raspberry pie then password. Nope. Then pi@IP. Nope.?
|
I was able to ping the IP. I then was able to verify that VNC was enabled. Now I can¡¯t remember what username and password combo to use when settiup the vnc connection. I should remember but this one brain doesn¡¯t retain like it use to. I thought is was pi-star then password. Nope. Tried raspberry pie then password. Nope. Then pi@IP. Nope.?
|
Dave ? ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev |
Another possible answer:? Sometimes when I boot my Pi it fails to recognize my Wifi so I have to wait until the Hospot timer tries again.? I set mine to 2 minutes.? Then it works as usual.? For some reason it turns on the hotspot on boot and I end up with a 10.10.10.10 address.? If you connect Ethernet at boot you can always come in on that address and see what is going on with Conky.? Your router might be hanging on to the old address (the way it should) as addresses are given a lease when they are assigned and that address will continue to be used as long as the device is used within the lease period.? Often youu can VNC into it using the hostname of the Pi, like vnc raspberrypi? try that.
|
Good evening All,
Created my first Build A Pi SD card last night.? Added a bunch of Jason's tools, Winlink, Direwolf, Hamclock, Conky etc. I shut the Pi down last night, and returned this eveining learn more and add more to it.? Powered it up and can't VNC into. I Go to my router and can see raspberrypi.? It has the same IP that it assigned to it last night.? But I cannot VNC into it. Any help would be greatly appreciated. 73, Dave KB7BYI |
Re: Latest Pat Winlink and rig contrl
#bap
Chris Huchel
Jason,
Something to note. The ARDOP PTT config is available in two locations in PAT Menu. One is in Manage PAt Winlink as you described before, the other is in Settings/Config. I had to make sure both were set to yes before my station would cooperate. Chris, KI7JOM |
Re: Js8call program features too large to use
#js8call
Just tried a few digferent resolutions again and its always the same with the js8 program. All the features are too large and wont match its window size like the terminal window. Terminal woll adjust sizing of letters amd numbers. Js8 is keeping all of its icons and things too massive to use.
|
Re: Js8call program features too large to use
#js8call
It seems like things like terminal frame are fine with me, just the js8 program.
|
Re: Js8call program features too large to use
#js8call
I'm having the same issue. My PI 3 A+ is nicely set up for my desktop or Toughbook. I tried to change the resolution?on the pad and it was a lost cause. I may have to get an Android phone terminal and ssh in and use sudo raspi-config to change the?resolution?that way. 73 Don Poaps New Westminster, BC VA7DGP DATA VA7QU ? VOICE Winlink: va7qu@... Subject://wl2k ? ? ? ? ? ALLSTAR ?530780 Hamshack Hotline 5971 Mid-Island Phone Mesh 2210 2232 ? ? ? ? ? ? ? ? ? ? On Fri, Feb 11, 2022 at 8:49 AM Jacob Lindsey ( KN4YAV ) and Kayla Lindsey ( KO4DEG ) <jmlredtail@...> wrote: Yea i set a few different resolutions and they dont affect the program features, just the entire resolution, which, size wise, im fine with. |