Re: Build a Pi 3.0.3 Released
Just an FYI:?Jason's entire suite (full install) performs perfectly for me even on a plain Raspi3, it does not need to be the 'B+' version. I am able to even run WSJT-X and GridTrack simultaneously, which was not possible with the older GridTracker release.
CPU temp hovers near 60-C, with no apparent problems for more than 2-weeks of 24/7 operation.
73 de Jerry - LU/K4OAM
On Wed, Aug 26, 2020 at 06:26 PM, Jonathan Scherch wrote:
Jason, I'm still running a Pi 3B+. Will 3.03 run ok on this older model?
Yes. It should run fine on the 3B+
?
--
73, de KM4ACK
|
|
|
Jason,
Would you also consider adding D-RATS to the mix of software?
Not sure if there is a better place to post this requests, but following Don example.
Thanks
Jared- W0JMR
|
Re: Pi 4 and using hot spot
see previous replies. The one Pat Menu pulls up.
73 Don Poaps
New Westminster, BC
VA7DGP DATA VA7QU ? VOICE
Subject://wl2k ? ? ? ? ??
 ? ? ? ? ? ? ? ? ? ??
  ??
?
On Thu, Aug 27, 2020 at 7:19 AM G.A.(Jerry) Minor < n5rke@...> wrote: Don,
Jason was trying to determine which of the two APRS programs included with Build-a-Pi you are using. Either YAAC or XASTIR.?
--
73 de N5RKE
|
Re: Pi 4 and using hot spot
Don,
Jason was trying to determine which of the two APRS programs included with Build-a-Pi you are using. Either YAAC or XASTIR.?
--
73 de N5RKE
|
Re: Pi 4 and using hot spot
Don Poaps
New Westminster, BC
VA7DGP DATA VA7QU ? VOICE
Subject://wl2k ? ? ? ? ??
? ? ? ? ? ? ? ? ? ??
??
?
Is there away to get a BC map
BC map in which program Don?
It seems where I downloaded the Off Line map for BC Aprsdroid has changed
Loaded up APRS.
Which APRS program are you using?
GPS didn't seem to track or beacon
Did the GPS have a lock on the satellites?
All I know is the GPS DIY gps I had on the roof of the car. This GPS worked in the house before I took the PI 4 out for it's road trip.
73 --
73, de KM4ACK
|
|
|
Re: Pi 4 and using hot spot
Is there away to get a BC map
BC map in which program Don?
It seems where I downloaded the Off Line map for BC Aprsdroid has changed
Loaded up APRS.
Which APRS program are you using?
GPS didn't seem to track or beacon
Did the GPS have a lock on the satellites?
All I know is the GPS DIY gps I had on the roof of the car. This GPS worked in the house before I took the PI 4 out for it's road trip.
73 --
73, de KM4ACK
|
|
|
Re: Build a Pi 3.0.3 Released
On Wed, Aug 26, 2020 at 06:26 PM, Jonathan Scherch wrote:
Jason, I'm still running a Pi 3B+. Will 3.03 run ok on this older model?
Yes. It should run fine on the 3B+ ? --
73, de KM4ACK
|
|
|
Re: Pi 4 and using hot spot
Is there away to get a BC map
BC map in which program Don?
Loaded up APRS.
Which APRS program are you using?
GPS didn't seem to track or beacon
Did the GPS have a lock on the satellites? --
73, de KM4ACK
|
|
|
Re: Build a Pi 3.0.3 Released
Jason, I'm still running a Pi 3B+. Will 3.03 run ok on this older model?
Thanks again. 73.
Jonathan
|
Mumble seems to suffer with noise. On a good strong signal, it¡¯s acceptable. But add typical HF noise and lots of unpleasant artifacts appear.?
I used Skype for a number of years and likely still would. That is the quality level to strive for.?
don
W6CZ
|
I got my Pi 4 out in the mobile today. Is there away to get a BC map. I see I had check download new map. I'm going to remove that.?
The Pat Menu started up. I started Bluetooth. Loaded up APRS. The GPS didn't seem to track or beacon. I have logged into hotspot. My icon aka wheelchair has not moved. I have to find FAQ or something on that program to follow my tracks, and have the map show a full map not a 1/2 with white and the other side as a map?
Later
Don va7dgp
|
Setting up duplex audio is the big stumbling block without using skype or some other 2nd party software. Mumble does not work well either. RigPi is a convoluted mess with it's audio. HTML 5 can do it but software very complex. Whoever solves IP duplex audio with open source software will be a real hero.
|
Noted. --
73, de KM4ACK
|
|
|
Dam autocorrect...
I'd vote for that too! ?
Neil VK3IG
If vote for that too!
Neil VK3IG
On Wed, 26 Aug 2020, 11:23 Wayne Thorn, < km4vrz@...> wrote: Yes, add freedv to the list..
Jason,
Would you consider adding FreeDV to the mix of software??
Thanks
Don - N5SKT
--
Wayne Thorn
km4vrz@...
813-662-9393
|
|
|
|
|
Jason,
Would you consider adding FreeDV to the mix of software??
Thanks
Don - N5SKT
|
Re: Build a Pi 3.0.3 Released
Hi Mike,
I'm glad you managed to install it!
toggle quoted message
Show quoted text
On 25.08.20 §Ô. 1:09, Mike - N5AQM wrote: EDIT: I was able to install it from file manager (just like windows)
by right clicking on the file and opening file and was then asked if I
wanted to install it! Worked and my problem?seems to be resolved with
the 2.2.1 version as I suspected! Then used the hold command and that
said it worked also...
--
73 Daff, LZ1DAF
|
Re: Build a Pi 3.0.3 Released
Hi Daff, EDIT: I was able to install it from file manager (just like windows) by right clicking on the file and opening file and was then asked if I wanted to install it! Worked and my problem?seems to be resolved with the 2.2.1 version as I suspected! Then used the hold command and that said it worked also... ?Thanks for the quick reply!
I got the file wsjtx_2.2.1_armhf.deb? into the download area and navigated there in terminal and executed the command sudo apt install ./wsjtx_2.2.1_armhf.deb
and got the following:
pi@raspberrypi:~/Downloads $ sudo apt install ./wsjtx_2.2.1_armhf.deb
Reading package lists... Done
E: Unsupported file ./wsjtx_2.2.1_armhf.deb given on commandline
pi@raspberrypi:~/Downloads $?
?
So I am not sure what to do here... I am a complete noob on this command line stuff. Appreciate your help. -Mike
?
|
Re: Build a Pi 3.0.3 Released
P.S. You can also download v.2.2.1 for your laptop from the link I sent in previous email. Just pick the right package for your laptop's OS. On August 24, 2020 8:23:23 PM UTC, Dafcho Tabakov <lz1daf@...> wrote:
Hi, Mike!
Get armhf version from here:
Then open a console (terminal window) in directory where is v.2.2.1 and install it via this command:
sudo apt install ./wsjtx_2.2.1_armhf.deb
It will overwrite v.2.2.2 with the old version.
If it is successful, then it's good to mark v.2.2.1 not to be updated via scripts, etc:
sudo apt-mark hold wsjtx
If later there is a new version with the corrected bug then unmark the package:
sudo apt-mark unhold wsjtx
73! Daff, LZ1DAF
On August 24, 2020 7:33:05 PM UTC, Mike - N5AQM <n5aqmdb@...> wrote:
There is an issue with WSJT-x ver 2.2.2 running WSPR in band hopping mode. It crashes! It also does it on my Laptop running the same version. I had an older version on another pi as well as an older version on my laptop and they both work fine.?
My problem is that I can't find an older version for the Pi. ver 2.2.1 which works ok on both machines. When I search for add/remove programs on the pi, it only comes up with the latest 2.2.2.?
Any suggestions?
Thanks!
-Mike
73! Daff, LZ1DAF
73! Daff, LZ1DAF
|
Don Poaps
G.A.(Jerry) Minor
km4ack
Jonathan Scherch, KK7PW