开云体育

That makes sense. I did that but still no templates seen. The good thing is that I’m no longer having the Pat modem turn off…

Here’s a screenshot of my config.json file to verify I’m adding the line correctly.

On Sat, Jul 10, 2021 at 01:43 Brian Dale <bdale.droid@...> wrote:

Same problem I had...I posted what I did to correct that. Deleted the line I added, reinstalled PAT with BAP, rebooted and it worked fine after that. I'm no expert but that's what I did to 3 different PIs and they are all working now.

On Sat, Jul 10, 2021 at 1:35 AM K3JRZ <k3jrz.jeff@...> wrote:

I have to be missing something because the green “PAT ACTIVE” item in Conky switches to a red “PAT OFF” when I add that line into the config.json file.

On Sat, Jul 10, 2021 at 01:22 Brian Dale <bdale.droid@...> wrote:

You have to add the line:

"forms_path": "/home/pi/.wl2k/Standard_Forms"??

On Sat, Jul 10, 2021 at 1:18 AM K3JRZ <k3jrz.jeff@...> wrote:

Ok, so I run the command “Pat configure”. Got that.? It opens the config.json file.?

I’m not a Raspberry Pi wizard and I don’t see any thing about the forms in the config.json file. Besides the path that is listed below, what do I need to add?

Thanks

On Sat, Jul 10, 2021 at 01:02 Brian Dale <bdale.droid@...> wrote:

As previously posted:

Use 'pat configure' to point to the template folder. E.g.
on a Mac: "forms_path": "/Users/walter/.wl2k/Standard_Forms"
on an Raspberry Pi: "forms_path": "/home/pi/.wl2k/Standard_Forms"?

Mine is up and running fine now. I downloaded the form package by "updating forms" within PAT and then put the forms path into the pat config file. After rebooting, I couldn't access PAT through the web interface. I played around a bit and then deleted the line I added in pat config and did a reinstall of PAT through BAP. Everything worked after that and it still knew where the forms were and worked fine. I'm not sure what the extra steps were all about but I duplicated it three times on two machines.??

On Sat, Jul 10, 2021 at 12:55 AM K3JRZ <k3jrz.jeff@...> wrote:

Manualky downloaded the form templates, but Pat doesn’t see them.

Do I need to do something for Pat to see the new forms?

Thanks

On Fri, Jul 9, 2021 at 22:06 Brian Dale <bdale.droid@...> wrote:

Also have to do this apparently:

Download templates from Winlink.org
Unzip the Standard_Forms archive
Use 'pat configure' to point to the template folder. E.g.
on a Mac: "forms_path": "/Users/walter/.wl2k/Standard_Forms"
on an Raspberry Pi: "forms_path": "/home/pi/.wl2k/Standard_Forms"

On Fri, Jul 9, 2021 at 10:04 PM Brian Dale via <bdale.droid=[email protected]> wrote:

BAP will update PAT. You have to run pat and select actions update forms template.

On Thu, Jul 8, 2021 at 10:50 AM Don Poaps <va7dgp@...> wrote:

LA5NTA

5:48 AM (1 hour ago)

Pat v0.11.0 has been released, and binaries for Linux, macOS and Windows are available at . Will the Build a Pi pull this latest release with the * Add support for Winlink HTML Forms ? 73

Don Poaps
New Westminster, BC
VA7DGP DATA
VA7QU ? VOICE


Winlink: va7qu@...
Subject://wl2k ? ? ? ? ?

ALLSTAR ?530780
HH# 5971
HH# 11384

Alberta Mesh# 5404

? ? ? ? ? ? ? ? ? ?

--

Thanks & 73,

Jeff

K3JRZ

K3JRZ.jeff@...

?#404

--

Thanks & 73,

Jeff

K3JRZ

K3JRZ.jeff@...

?#404

--

Thanks & 73,

Jeff

K3JRZ

K3JRZ.jeff@...

?#404

--

Thanks & 73,

Jeff

K3JRZ

K3JRZ.jeff@...

?#404