开云体育

Hello I tried to upload some pictures to this forum (folder KD 860 Fi) with no success. And now I can't even see most of the older pictures anymore. I have tried multiple browsers, windows 8 and 10

Rien I hope the rudder problem is now solved; If not, and this is valid for all my boat rudders. It is important that the leading edge Epoxy filler is going not higher as shown. Otherwise, the angle

Hope the gluing up of the rudder blades has gone well. I also had problems with the plywood failing while bending the ply around. On the second blade I thought it was all good, but then as I was

Hi Rien, there was quite a link between us K designs builders here in New Zealand.I was following Rodney, who built Sparta, from when he started work, and I was also going to build a KD650. I changed

Thanks, Bryan! I appreciate your comments. It so happens that I have been poring over your blog, especially the rudder part, over the last week. Also Hamish’ photos and the KD650 Sparta blog have

Rien, in many cases the quality of plywood today causes failures of the rudder foils when bending them in the jig. Close the angle up a bit with spacers and do a small test. You can check my building

Hello all I added a couple of pictures to KD860 FI folder. I had to remove (and reinstall) a wall of my father's garage to get the boat out. I must say that the shell is very strong construction, it

Hi Rien? Found the photos thank you. What is going one with the rudders? You can make a water trail. Also making the plywood wet. Problem is to try the plywood.Sounds good your plan. Point is making

Hello Interesting to turn a hull alone. There where a lot of thoughts going in. But the result looks fine. First thinking and then doing a very good example and thanks for the pictures Cheers Bernd

With my two last posts I uploaded 10 Pics, which I can't see now on this site. The yahoo email telling me about the posts did contain the pics, so they must have been arrived. The texts alone are not

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the k-designs group. File : /_KDlogo.pdf Uploaded by : shorelinefencing

Hi Bernd, Yes, this is my ECO6. I’m getting close to finishing. At the moment I’m making (breaking ?) rudder foils. Next is standing the mast and rigging, some electrical wiring, fit outboard

For to turn the hulls from upright to bottom up position I place lifting slings transversal under the keel (green in the pic) and fix one side with clamps at the sheer. The other sides are hinged in

For lifting the hulls with the cranes I use the special nuts I embedded last year in the hulls as access points (4 per hull). I prepared 6 mm plywood strips fitting in 2 washers each (2 * 2 mm thick)

Ok, Bernd, I will post some more details and pics in my original thread. https://groups.yahoo.com/neo/groups/k-designs/conversations/messages/7795

My experience so far with my solar electric boat has been mostly good. I have learned from my mistakes as most people do. I have proven in my boat, with two major trips that used 100% solar energy

Try linux work so good with all computor Old and new Ave firefox in it Stephane blanchette ANJALEC CONSTRUCTION 438-837-4246 Samsung Galaxy.

Hi Hans Because I am in full war with Windows 10 and can not find your private address anymore. Nice pictures on a typical Dutch on a nice day; You are happy with the new sail? I know the problem with

Hi Phil The first link was working; Nice boat by the way. What is your experience so far? The Nickel/Zink rechargeable batteries will be 2020 in production. Cheers Bernd

I will try putting my one link on a direct reply and see if that works. https://www.youtube.com/playlist?list=PLPg4n9e1vhPBBC53NTbXIivrssL42bNFc