Are the JackAl docs different than the BuyDisplay docs? Try to get a close up of the connector edge and post that.
Jack, W8TEE
On Thursday, March 7, 2019, 3:14:46 PM EST, Vince Loschiavo <vince320@...> wrote:
Must be me...Purchased the 7 inch display and connections on in manual 2 do not match..could someone annotate the connections to this board? please.
Thanks
Vince
N2AIE
|
Must be me...Purchased the 7 inch display and connections on in manual 2 do not match..could someone annotate the connections to this board? please.
Thanks
Vince
N2AIE
|
Re: Mounting teensy and audio board Jackal Board
I think that I will just wait until Jack and Al have updated their documentation and Jack has finished examining his V5 board.? All may be revealed.
73 All
Kevin VK3DAP / ZL2DAP
--
73
Kevin VK3DAP / ZL2DAP
|
Re: Recommended Mods (& not...)
The coils are pulled and replaced by 680 nH SMD inductors:
I have parts coming in Friday (I hope).
- John
toggle quoted message
Show quoted text
On 3/6/2019 2:28 PM, k7da wrote: what are these two l's changed to?
dave k7da
On 3/6/2019 2:59 AM, John Sutter wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Recommended Mods (& not...)
what are these two l's changed to?
dave k7da
toggle quoted message
Show quoted text
On 3/6/2019 2:59 AM, John Sutter wrote: Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Recommended Mods (& not...)
After looking at the spec sheet, they, (5003), appears to be a suitable, (maybe superior?). replacement for the 5403 which is a 400 mw coil, not as I said before 200. Little bit higher coil resistance, same operating voltage, and they're only used for bandswitching. I'll let you know how they work. Ron W0QVJ
Sent from my Galaxy Tab? E
toggle quoted message
Show quoted text
-------- Original message -------- From: "eyelessmisfit via Groups.Io" <eyelessmisfit@...> Date: 3/6/19 1:24 PM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
Hope not too much, as I guess that's what I'm getting...;} Difference is in the coil sensitivity 150 mw instead of 200. (Going to need to start using my glasses when ordering parts!) Thanks again, Jack! Ron W0QVJ
Sent from my Galaxy Tab? E
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 12:37 PM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
I saw an ad by them for $8.60/4, but that was for the Axiom V23105-A5003-A201, not the Axiom V23105-A5403-A201. Does it make a difference??
Jack, W8TEE
On Wednesday, March 6, 2019, 1:58:30 PM EST, eyelessmisfit <eyelessmisfit@...> wrote:
FYI, ebay, (chipsgate,was the seller), charged $8.50 for 4, and they shipped today. Ron W0QVJ
Sent from my Galaxy Tab? E
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 11:14 AM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
Arrow Electronics carries them at $2.20, 10 for $2.10, or 35 at $1.96. Everyone probably knows they don't charge for shipping, so order a bunch and sell them to club members.
Jack, W8TEE
On Wednesday, March 6, 2019, 12:13:50 PM EST, eyelessmisfit <eyelessmisfit@...> wrote:
Just ordered from eBay, recommended relay part no.; Axiom V23105-A5403-A201 73's Ron W0QVJ
Sent from my Galaxy Tab? E
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 9:36 AM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
I've slept since the post that detailed the relays, but I think I recall they are made for RF work by Axiom. You can search the BITX20 Forum for the correct part number.
Jack, W8TEE
On Wednesday, March 6, 2019, 11:29:07 AM EST, PeteWK8S via Groups.Io <pmeier@...> wrote:
What are recommended relays (model and source)? On Mar 6, 2019, at 6:49 AM, jjpurdum via Groups.Io < jjpurdum@...> wrote:
If you're running the V4 or earlier board, it would appear that the relay changes will do the most good. The V4 units we have test okay for all bands but 15-10M, which we do use, so we haven't messed with the relay mod. We're still checking out the V5 board.
Jack, W8TEE
On Wednesday, March 6, 2019, 5:59:55 AM EST, John Sutter < jds@...> wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Recommended Mods (& not...)
Hope not too much, as I guess that's what I'm getting...;} Difference is in the coil sensitivity 150 mw instead of 200. (Going to need to start using my glasses when ordering parts!) Thanks again, Jack! Ron W0QVJ
Sent from my Galaxy Tab? E
toggle quoted message
Show quoted text
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 12:37 PM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
I saw an ad by them for $8.60/4, but that was for the Axiom V23105-A5003-A201, not the Axiom V23105-A5403-A201. Does it make a difference??
Jack, W8TEE
On Wednesday, March 6, 2019, 1:58:30 PM EST, eyelessmisfit <eyelessmisfit@...> wrote:
FYI, ebay, (chipsgate,was the seller), charged $8.50 for 4, and they shipped today. Ron W0QVJ
Sent from my Galaxy Tab? E
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 11:14 AM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
Arrow Electronics carries them at $2.20, 10 for $2.10, or 35 at $1.96. Everyone probably knows they don't charge for shipping, so order a bunch and sell them to club members.
Jack, W8TEE
On Wednesday, March 6, 2019, 12:13:50 PM EST, eyelessmisfit <eyelessmisfit@...> wrote:
Just ordered from eBay, recommended relay part no.; Axiom V23105-A5403-A201 73's Ron W0QVJ
Sent from my Galaxy Tab? E
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 9:36 AM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
I've slept since the post that detailed the relays, but I think I recall they are made for RF work by Axiom. You can search the BITX20 Forum for the correct part number.
Jack, W8TEE
On Wednesday, March 6, 2019, 11:29:07 AM EST, PeteWK8S via Groups.Io <pmeier@...> wrote:
What are recommended relays (model and source)? On Mar 6, 2019, at 6:49 AM, jjpurdum via Groups.Io < jjpurdum@...> wrote:
If you're running the V4 or earlier board, it would appear that the relay changes will do the most good. The V4 units we have test okay for all bands but 15-10M, which we do use, so we haven't messed with the relay mod. We're still checking out the V5 board.
Jack, W8TEE
On Wednesday, March 6, 2019, 5:59:55 AM EST, John Sutter < jds@...> wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Recommended Mods (& not...)
I saw an ad by them for $8.60/4, but that was for the Axiom V23105-A5003-A201, not the Axiom V23105-A5403-A201. Does it make a difference??
Jack, W8TEE
On Wednesday, March 6, 2019, 1:58:30 PM EST, eyelessmisfit <eyelessmisfit@...> wrote:
FYI, ebay, (chipsgate,was the seller), charged $8.50 for 4, and they shipped today. Ron W0QVJ
Sent from my Galaxy Tab? E
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 11:14 AM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
Arrow Electronics carries them at $2.20, 10 for $2.10, or 35 at $1.96. Everyone probably knows they don't charge for shipping, so order a bunch and sell them to club members.
Jack, W8TEE
On Wednesday, March 6, 2019, 12:13:50 PM EST, eyelessmisfit <eyelessmisfit@...> wrote:
Just ordered from eBay, recommended relay part no.; Axiom V23105-A5403-A201 73's Ron W0QVJ
Sent from my Galaxy Tab? E
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 9:36 AM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
I've slept since the post that detailed the relays, but I think I recall they are made for RF work by Axiom. You can search the BITX20 Forum for the correct part number.
Jack, W8TEE
On Wednesday, March 6, 2019, 11:29:07 AM EST, PeteWK8S via Groups.Io <pmeier@...> wrote:
What are recommended relays (model and source)? On Mar 6, 2019, at 6:49 AM, jjpurdum via Groups.Io < jjpurdum@...> wrote:
If you're running the V4 or earlier board, it would appear that the relay changes will do the most good. The V4 units we have test okay for all bands but 15-10M, which we do use, so we haven't messed with the relay mod. We're still checking out the V5 board.
Jack, W8TEE
On Wednesday, March 6, 2019, 5:59:55 AM EST, John Sutter < jds@...> wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Recommended Mods (& not...)
FYI, ebay, (chipsgate,was the seller), charged $8.50 for 4, and they shipped today. Ron W0QVJ
Sent from my Galaxy Tab? E
toggle quoted message
Show quoted text
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 11:14 AM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
Arrow Electronics carries them at $2.20, 10 for $2.10, or 35 at $1.96. Everyone probably knows they don't charge for shipping, so order a bunch and sell them to club members.
Jack, W8TEE
On Wednesday, March 6, 2019, 12:13:50 PM EST, eyelessmisfit <eyelessmisfit@...> wrote:
Just ordered from eBay, recommended relay part no.; Axiom V23105-A5403-A201 73's Ron W0QVJ
Sent from my Galaxy Tab? E
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 9:36 AM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
I've slept since the post that detailed the relays, but I think I recall they are made for RF work by Axiom. You can search the BITX20 Forum for the correct part number.
Jack, W8TEE
On Wednesday, March 6, 2019, 11:29:07 AM EST, PeteWK8S via Groups.Io <pmeier@...> wrote:
What are recommended relays (model and source)? On Mar 6, 2019, at 6:49 AM, jjpurdum via Groups.Io < jjpurdum@...> wrote:
If you're running the V4 or earlier board, it would appear that the relay changes will do the most good. The V4 units we have test okay for all bands but 15-10M, which we do use, so we haven't messed with the relay mod. We're still checking out the V5 board.
Jack, W8TEE
On Wednesday, March 6, 2019, 5:59:55 AM EST, John Sutter < jds@...> wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Recommended Mods (& not...)
Arrow Electronics carries them at $2.20, 10 for $2.10, or 35 at $1.96. Everyone probably knows they don't charge for shipping, so order a bunch and sell them to club members.
Jack, W8TEE
On Wednesday, March 6, 2019, 12:13:50 PM EST, eyelessmisfit <eyelessmisfit@...> wrote:
Just ordered from eBay, recommended relay part no.; Axiom V23105-A5403-A201 73's Ron W0QVJ
Sent from my Galaxy Tab? E
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 9:36 AM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
I've slept since the post that detailed the relays, but I think I recall they are made for RF work by Axiom. You can search the BITX20 Forum for the correct part number.
Jack, W8TEE
On Wednesday, March 6, 2019, 11:29:07 AM EST, PeteWK8S via Groups.Io <pmeier@...> wrote:
What are recommended relays (model and source)? On Mar 6, 2019, at 6:49 AM, jjpurdum via Groups.Io < jjpurdum@...> wrote:
If you're running the V4 or earlier board, it would appear that the relay changes will do the most good. The V4 units we have test okay for all bands but 15-10M, which we do use, so we haven't messed with the relay mod. We're still checking out the V5 board.
Jack, W8TEE
On Wednesday, March 6, 2019, 5:59:55 AM EST, John Sutter < jds@...> wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Recommended Mods (& not...)
Just ordered from eBay, recommended relay part no.; Axiom V23105-A5403-A201 73's Ron W0QVJ
Sent from my Galaxy Tab? E
toggle quoted message
Show quoted text
-------- Original message -------- From: "jjpurdum via Groups.Io" <jjpurdum@...> Date: 3/6/19 9:36 AM (GMT-07:00) Subject: Re: [JackAl] Recommended Mods (& not...)
I've slept since the post that detailed the relays, but I think I recall they are made for RF work by Axiom. You can search the BITX20 Forum for the correct part number.
Jack, W8TEE
On Wednesday, March 6, 2019, 11:29:07 AM EST, PeteWK8S via Groups.Io <pmeier@...> wrote:
What are recommended relays (model and source)? On Mar 6, 2019, at 6:49 AM, jjpurdum via Groups.Io < jjpurdum@...> wrote:
If you're running the V4 or earlier board, it would appear that the relay changes will do the most good. The V4 units we have test okay for all bands but 15-10M, which we do use, so we haven't messed with the relay mod. We're still checking out the V5 board.
Jack, W8TEE
On Wednesday, March 6, 2019, 5:59:55 AM EST, John Sutter < jds@...> wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Recommended Mods (& not...)
Thanks Jack On Mar 6, 2019, at 9:36 AM, jjpurdum via Groups.Io < jjpurdum@...> wrote:
I've slept since the post that detailed the relays, but I think I recall they are made for RF work by Axiom. You can search the BITX20 Forum for the correct part number.
Jack, W8TEE
On Wednesday, March 6, 2019, 11:29:07 AM EST, PeteWK8S via Groups.Io < pmeier@...> wrote:
What are recommended relays (model and source)? On Mar 6, 2019, at 6:49 AM, jjpurdum via Groups.Io < jjpurdum@...> wrote:
If you're running the V4 or earlier board, it would appear that the relay changes will do the most good. The V4 units we have test okay for all bands but 15-10M, which we do use, so we haven't messed with the relay mod. We're still checking out the V5 board.
Jack, W8TEE
On Wednesday, March 6, 2019, 5:59:55 AM EST, John Sutter < jds@...> wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
Pete Meier
pmeier at
Amateur Radio Callsign: WK8S
|| I never lose. If I don't win, I learn. -?unknown author ||
|
Re: Recommended Mods (& not...)
I've slept since the post that detailed the relays, but I think I recall they are made for RF work by Axiom. You can search the BITX20 Forum for the correct part number.
Jack, W8TEE
On Wednesday, March 6, 2019, 11:29:07 AM EST, PeteWK8S via Groups.Io <pmeier@...> wrote:
What are recommended relays (model and source)?
On Mar 6, 2019, at 6:49 AM, jjpurdum via Groups.Io < jjpurdum@...> wrote:
If you're running the V4 or earlier board, it would appear that the relay changes will do the most good. The V4 units we have test okay for all bands but 15-10M, which we do use, so we haven't messed with the relay mod. We're still checking out the V5 board.
Jack, W8TEE
On Wednesday, March 6, 2019, 5:59:55 AM EST, John Sutter < jds@...> wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Recommended Mods (& not...)
What are recommended relays (model and source)?
toggle quoted message
Show quoted text
On Mar 6, 2019, at 6:49 AM, jjpurdum via Groups.Io < jjpurdum@...> wrote:
If you're running the V4 or earlier board, it would appear that the relay changes will do the most good. The V4 units we have test okay for all bands but 15-10M, which we do use, so we haven't messed with the relay mod. We're still checking out the V5 board.
Jack, W8TEE
On Wednesday, March 6, 2019, 5:59:55 AM EST, John Sutter < jds@...> wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Recommended Mods (& not...)
If you're running the V4 or earlier board, it would appear that the relay changes will do the most good. The V4 units we have test okay for all bands but 15-10M, which we do use, so we haven't messed with the relay mod. We're still checking out the V5 board.
Jack, W8TEE
On Wednesday, March 6, 2019, 5:59:55 AM EST, John Sutter <jds@...> wrote:
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Recommended Mods (& not...)
Of the recommended mods to the stock uBitx, which are still
recommended when using the JackAl board?
I'll be changing L5 & L7 and probably the relays too.
John
W1JDS
|
Re: Mounting teensy and audio board Jackal Board
I now think that if there is any likelihood of wanting to access other pins on the Teensy, we should probably follow the instructions of James Zdunic , KM4TXR, /g/JackAl/attachment/475/1/CPU%20PINS%20_2_.pdf. I now have the bits and pieces, but am a bit scared that I might make an expensive mistake! 73, Kevin VK3DAP / ZL2DAP -- Kevin B. G. Luxford kbgluxford@... -- 73 Kevin VK3DAP / ZL2DAP
|
Hi,
Did everybody connect through the single pin marked VUSB from the Jackal board to the Teensy?
Keith M6OLP
|
Re: Mounting teensy and audio board Jackal Board
Yes it was one and the same.. Kevin, you outlined the procedure as you saw it and needed confirmation of that.. I sort of need a dummies guide myself lol?
Is not my original query regharding the procedure for attaching the audio board to the Teensy and then to thge JackAl board rendered obsolete by? James Zdunic's CPU-Pins_2.pdf posting?
73, Kevin VK3DAP / ZL2DAP
--
? Kevin B. G. Luxford
? kbgluxford@...
--
73
Kevin VK3DAP / ZL2DAP
|
Re: Mounting teensy and audio board Jackal Board
Is not my original query regharding the procedure for attaching the audio board to the Teensy and then to thge JackAl board rendered obsolete by James Zdunic's CPU-Pins_2.pdf posting?
73, Kevin VK3DAP / ZL2DAP
--
Kevin B. G. Luxford
kbgluxford@...
--
73
Kevin VK3DAP / ZL2DAP
|
jjpurdum