开云体育

The SRAM battery has died on the PCMCIA /ROM/ memory card.? Far right hand side from the front ....lot's of screws though. The batteries are commonly available? ...the 8924 on used one of the 3v

Better to say: And you almost can't send too many pictures, either contained in your post or uploaded to the files section.

Gang, When replying to a post, please try to avoid automatically quoting (including) a lot, or all of the prior message.? ?Often you can just leave the old stuff out completely. With the AA battery

I'll look into the battery changing.? I hate things with batteries in them for long term usage.? About as bad as some things that use that Dallas clock chip that has to be changed about every 10 or

Put it on your to-do list to CHANGE those AA batteries pronto!? ?Whether that's your immediate problem or not.? ?On all three sets, too. When you do I pray you'll find not a spot of evil battery

Hank, I did not know about changing batteries.? I have never changed any batteries in the sets. I actually have 3 of the sets.? The oldest I bought over 10 years ago.? It was only opened by me 2

Ralph, I'm going to take a shot at this even though you have way more operating experience than I have. Have you ever changed the two AA cells since you've owned the instrument?? They should be

What would cause a 8924c to loose the memory. That is I had it setup to come up in a FM service type mode by the command POWERON. Now it reverts back to the cell phone test screen. It has worked well

There are several things that will cause that if the settings are wrong. 1.? You have the tracking generator turned on2.? ?The tracking generator is set too high3 The RF in is selected instead of

Not sure if I hit a setting but my trace is not settling at the bottom of the scope - it is about three-quarters of the way to the top.? The reference level is at -10db.? Is there something else I

The following files have been uploaded to the Files area of the [email protected] group. * /HP 8935/E8935 EPSG087543.pdf (

Hi Patrick You might find this article interesting ?by Agilent / HP 8935? E6380A Amtronix Instruments, Inc Also did find a service manual Part number E6380-90015 as apparently there is a family of

Hi all! Happy to have found this group. I've owned my 8935 for about two years now and it's been great for my radio needs. However recently it's started throwing the AFCI breaker for my lab. I've

Yes - that was the kit I had used where you sent back the card, etc.? ?Ok well again I was just curious.? And yes, a screw gun would help big time with this work. Thanks so much for all of the info

This was in the files.? All or almost all of the Yahoogroup files are here.? It's just a matter of finding them.? Ralph helped once again by giving me the file title. HP-8924C_100W_upgrade.pdf (

It was over 10 years ago I bought the upgrade 60 watt? kit from ebay .? It had the attenuator, an emblem to paste over the BNC and a card to up load the info.? I had to send the card back for a $

Yes - I saw those pads on eBay and that was what I did with the one 8924c that was upgraded.? You got a pad where you removed the one that was there and soldered in the new one which had the higher

You really need an almost 20 db pad as the 3 watt version already has a 4 db pad that is removed.? I think the heat sink is the same for the 60 watt and the 3 watt versions, so all you need is the

Thanks Ralph - that is an option and there were other posts that mention where to go to create the offset in the power.? You would need a 16 dB attenuator ideally to put the 100 watts down to 3 watts

You may want to do like I did a few years back.? Just buy an attenuator from ebay of a 100 watt rating that will fit the heatsink that is already in the 8924C.? There were some files in the files