开云体育

either will work.

The 50k resistors, how critical is that value, I have 47k and 56k will either of these work? I guess I could use 2x100k if needed. Bill N7OQ

Wow again, great information, I get my lm-1881 Thursday or wed. Will let you know how it works out, thanks everyone, Bill N7OQ

To use the GBS-8200 converter with the hp-8924c service monitor to use with an external VGA monitor. Obtain: 50 K ohm SMD resistors 4 required LM1881N IC sync seperator.1 UF capacitor--2 required680

My guide: https://tabajara-labs.blogspot.com/2021/01/como-ligar-um-monitor-vga-no-hp-e8285a.html ---8<---Corte aqui---8<--- http://www.tabajara-labs.blogspot.com http://www.tabalabs.com.br

Bill Here are a couple of old things i saved re getting the GBS-8200 workings with 8924 from the old Yahoo groups. There is also one on power supply repair plus some notes on power supply caps I

Hi group, I want to replace the CRT monitor in my 8924 and bought a GBS-8200 board. Well I saw a picture where they plugged it into the green (Y) rca jack on the 8200 board and this worked to a degree

Thank you everyone, I’ll order 105 degree caps and do a recap. So far everything else seems to be working. This is a great forum. Bill N7OQ

As others said, it is most likely the capacitors.? About 90% or more switching supply problems are the capacitors. I had an 8924c that acted similar.? I took a hot air gun from a SMD rework station

there is a write up in the files section ...or at least there used to be from the old hosting service. usually you are missing the green led on the rear of the unit which is the 15 volt standby

It is a very common issue with these power supplies. All the electro caps go faulty. Especially the little ones on the small boards. You need to change them all for 105 degree rated caps. The old 85

Hello group, thanks for letting me join,? My name Is Bill and call is N7OQ. I got a free HP-8924C that the guy said needed a new power supply. Well I put Some power to it and nothing, then I removed

All I found is this user manual: http://notes-application.abcelectronique.com/018/18-22432.pdf An interesting piece.? What is the matter with a 3v battery that reads 3.1v??? did you slip with the

Hello I have a HP11758 Multipath test set and it contains an rf power meter that I suspect is similar to HP437 power meter.? This unit has a soldered-in Panasonic 3 volt lithium battery and it

There are 2x OCXOs in the E8285A. High stability and CDMA which is pll locked to the high stability. The location is shown on page 89 of the E8285-90033 Agilent Technologies E8285A CDMA Mobile Station

Find a list of ATSC pilot frequencies.? They are usually network disciplined.? Try several - I see 2hz variation between them in my area.? This way you can judge the warmup drift of your

Penultimate update to the LCD saga (link to my blog not to load the group. Google translator is your friend) https://tabajara-labs.blogspot.com/2021/03/finalmente-eu-consegui-lcd-no-e8285a.html

It should be listed in options somewhere on the menu screens or on a sticker on the back. The High Precision unit is a big plug in metal box about 10 cm square and 1 cm deep metal can along with

Greetings! I want to know if my HPE8285A has the high-precision reference unit. Where should it be located? If it doesn't have it, how can I install? Ok, I know I can use an external GPSDO signal

It would be nice to have a backup of the present system. I ran into the same problem with another Agilent unit. E7495 I had to alter the code on the update card and re install the update. It made me