¿ªÔÆÌåÓý

Date
Re: I'm officially lost now with this 8753ES
To help me in my fault isolation efforts, Pete Manfre has offered to mail me a new, never used 08753-60162 A11 PLL board.? (Thank You Pete!) This will help immensely.? The trouble with the HP
By Peter Gottlieb · #95078 ·
Re: 5385A error 52
Can't seem to find a way to alter the behavior of NI Max. However, I did find that I can write w/o issue (example: sending DR HELLO puts "HELLO" on the display) and I can write/read if I wait for the
By Mark Bielman · #95077 ·
Re: HP8563 HV supply repair
Hello, ? Just a short update. All components except the transformer removed. It was fairly easy to remove the goop, but no chemicals would do the trick (not even silicone remover) so I ended up with
By Staffan · #95076 ·
Re: I'm officially lost now with this 8753ES
Thank you soooo much. Really appreciate it.
By amirb · #95075 ·
Re: I'm officially lost now with this 8753ES
Thank you Yves, that's fantastic! Peter
By Peter Gottlieb · #95074 ·
SG4 Service Manual
Please excuse this my intrusion in an HP forum with a request non-HP-related, but I am in desperate need of the Service Manual of the Wandel & Goltermann SG4 Display Unit. Google is of no help...? I
By Alberto di Bene · #95073 ·
E5500 licence
I have bought a 70420A phase noise test set - the heart of E5500 phase noise measurement system and used it with HP3561A and, later, with HP89441A samplers.? It needs a PC software package to be
By Leo Bodnar · #95072 ·
Re: 5385A error 52
Reading the manual of the counter , I verified the command to get te ID is "ID" or "SI". The instruments doesn't support the SCPI standard command syntax . On Agilent I/O there is the possibility to
By Maurizio IZ1MDJ · #95071 ·
Re: 5385A error 52
Hi Mark , I suppose teh counter interface was setted on listen mode at first. You can check if the NI Max is sending *IDN? command during the search for instruments. May be the counter doesn't support
By Maurizio IZ1MDJ · #95070 ·
Agilent 16700B/16702B Manuals
I am looking for the User manual and also the service guide for the 16700B/16701B/16702B series mainframe. I'm pretty sure I have seen it, but cannot find it now... And I don't seem to be able to find
By Maurice Smulders · #95069 ·
Re: I'm officially lost now with this 8753ES
Hi I have the original CLIP manual for 8753D and I have done a PDF and uploaded at http://www.ko4bb.com/getsimple/index.php?id=manuals To download
By Yves Tardif · #95068 ·
Re: I'm officially lost now with this 8753ES
I ordered the CLIPs from the ebay seller who likely got them from Manuals Plus which is now gone. Nothing is obviously wrong with the VCO drive to the YTO.? I say "obviously" because the waveform has
By Peter Gottlieb · #95067 ·
Re: I'm officially lost now with this 8753ES
The schematic is for 08753-60162, so it matches what you have. I would monitor the voltage across R43 (the 40 Ohm power resistor) as you tune the YTO. It should be a fairly linear function of
By pianovt · #95066 ·
5385A error 52
Hi all. So, hooked up my acquired 5385A to my HP-IB (GPIB) network and it crashed! The unit has "Error 52" on the display. Tried it all by itself and same issue. (This is with NI MAX... search for
By Mark Bielman · #95065 ·
Re: I'm officially lost now with this 8753ES
Thanks, just ordered one.
By Peter Gottlieb · #95064 ·
Re: I'm officially lost now with this 8753ES
It's available on eBay listed as 8753D CLIP. I bought mine that way. Artek doesn't seem to have it. Not sure if the eBay seller is licensed to sell it or not, but it's been years since I bought, and
By Colby Burkett · #95063 ·
Re: I'm officially lost now with this 8753ES
Thanks.? I've been working off of the 8753B CLIP, not too much has seemed to have changed.? What is the part number for A11 in the 8753D?? In my ES it is 08753-60162. What I'm seeing is that the
By Peter Gottlieb · #95062 ·
Re: I'm officially lost now with this 8753ES
Maybe this will be helpful. It's from the 8753D, but should be the same for the ES. Vladan
By pianovt · #95061 ·
Re: HP/Keysight/Agilent 34401A DMM power transformer
Siggi Again, thank you. Amazing (to me) the Keysight part is only 10 dollars more than the Chinese eBay replacements. So no contest there....And the video you linked shows the transformer hanging on
By victor smith · #95060 ·
Re: HP/Keysight/Agilent 34401A DMM power transformer
Then buy it from Keysight [ https://www.keysight.com/my/faces/partDetail.jspx?partNumber=34401-87901]. The registration process is a bit of a PITA, but the one time I bought a part from them it was
By Sigur?ur ?sgeirsson · #95059 ·