CHECK OUT THE WIKI The purpose of the wiki is mainly to allow you to find information on instruments, either from either
- The model number
- The function(s) listed below. Some instruments have multiple functions - for example, the 4195A is a VNA, spectrum analyzer and an impedance analyzer. Therefore the 4195A is listed in multiple categories
Please also check out HPWiki available here:
- Accessory kits - various types
- AC power analyzers - PA2201A and PA2203A
- AC power supplies 6811C, 6812C, 6813C
- Airlines
- Arbitrary waveform generators M8194A
- Amplifiers?493A, 495A?
- Attenuators (optical) 8156A, 8157A, 8158B, 81566A, 81576A,?
- Attenuators (RF) 8494A
- Attenuator set (500 Ω) 350C
- Attenuator set (600 Ω) 350D
- Attenuator switch driver
- Audio analyzers? 8903A, 8903B, 8903E,? ?
- Base station test sets
- Bit error rate testers (BERTs)
- Cables
- Capacitance meters U1701A, U1701B, 4272A, 4278A, 4279A
- Capacitor Bridge 4270A,
- Capacitor standards 16380A, 16380C,?
- Carrier noise test setsi
- Cesium frequency standards
- Clamp ammeters
- Close field probes
- Crystal Impedance E4915A, E4916A
- Data Acquisition Systems (DAQs)
- DC power analyzers
- DC power supplies 6030A , 6031A , 6032A, 6033A, 6035A, 6131C, 6621A, 6622A, 6623A, 6624A, 6627A, 6255A, 6645A, 6671A, 6672A, 6673A, 6674A, 6675A, 62003A, 62003C, 62003E, 62004A, 62004B, 62004E, 62005A, 62005B, 62005E, 62006A, 62006B, 62006E, 62010A, 62010C, 62010E, 62012A, 62012C, 62012E, 62015A, 62015C, 62015E, 62018A, 62018C, 62018E, 62024A, 62024C, 62024E, 62028A, 62028C, 62028E, 62048A, 62048C, 62048E
- Delay lines
- Detectors
- Device current waveform analyzers
- Digital communications analyzers
- Directional couplers
- Distortion analyzers 330B, 330C, 330D, 331A, 332A, 333A, 334A, 339A, 8903A, 8903B, 8903E,???
- Dynamic measurement DC source
- Electrometers
- Fading simulators
- Femto ammeters
- Filters
- Frequency counters 522B, 5342A 5343A 5352B
- Frequency standards?
- Function Generators ? 3310A,? 8165A,
- GPIB controllers, extenders, cables etc.
- GPS frequency standards
- Harmonic mixers
- High resistance meters 4339B
- High resistance meter fixtures 16008B
- HEV EV Grid Emulators and Test Systems
- In-circuit test systems
- Impedance analyzers 4195A, 4291A, 4291B, 4395A, 4396A, 4396B, 4294A, E4990A, E4991A
- Impedance Analyzer Accessories
- Impedance / Gain Phase analyzer 4194A
- Impedance Meter 4193A,
- Isolators
- LCR meters? U1701A, U1701B, U1731A,? U1731B, U1731C, U1732A, U1732B, U1732C, U1733C, 4191A , 4192A, 4194A, 4195A, E4196A,? 4216A, 4260A, 4261A, 4262A? 4263A, 4263B, 4271B, 4274A, 4275A, 4276A , 4277A, 4284A, 4285A, 4286A, 4287A, 4291A, 4291B, 4294A, 4332A, 4342A, 4395A, 4396A, 4396B, E4980A and E4980AL
- LCR meter calibration devices? 16380A 42030A? 42090A, 42091A and 42100A
- LCR meter accessories
- 2-Terminal BNCs.
- 4-Terminal Pair (BNC connectors)
- Cable extension 16048A, 16048D, 16048E, 16048G, 16048H
- DC current bias accessories 42841A, 42842A, 42842B, 42842C, 42843A
- DC voltage bias accessories 16065A, 16065C,
- Kelvin clips 16089A, 16089B, 16089C,16089E
- Lead Components 16047A,16047B, 16047D, 16047E
- Material 16451B, 16452A
- Probes 42941A
- SMD 16034E, 16034G, 16034H
- 2-port 16096A
- 7 mm (APC7)
- 2-Terminal BNCs.
- LCZ meters? 4276A, 4277A,
- Lightwave clock / data receivers
- Lightwave converter
- Lightwave component analyzer
- Lightwave measurement system mainframes
- Lightwave polarization analyzers 8509B
- Logic analyzers
- Nemo wireless network solutions.
- Noise and interference test set
- Noise figure analyzers
- Noise sources 346A, 346B. 346C ,
- Matching pads (50 ohm to 75 ohm or similar)
- Materials test equipment
- Microwave repeaters
- Microwave downconverters 70427A
- Microwave / THz sources
- Milliammeter 428B
- Milliohm meter
- Mobile communications DC source
- Modular instruments
- AXIe
- Data acquisition (DAQ)
- USB
- PXIe
- Modulation analyzers
- Multimeters 427A, 970A
- Optical attenuators
- Optical heads
- Optical sources
- Optical spectrum analyzers
- Oscilloscopes 120A, 120AR, 120B, 122A, 130A, 130B, 130BR, 130C, 140A, 140B, 141A, 150A, 150AR, 160B, 180A, 180AR, 180CD, 181A, 181AR, 181T, 181TR, 182C, 182T, 183A, 183B, 184A, 184B, 185A, 185B, 1200A, 1200B, 1220A, 1221A, 1703A, 1707A, 1707B, 1710A, 1710B, 1715A, 1722A, 1725A, 1726A, 1740A, 1741A, 1742A, 1743A, 1744A, 1746A, 1980A, 1980B, 5403A, 6000A, 6000L, 16533A, 16534A, 54100A, 5410B, 54100C, 5100D, 54111D, 54120A, 54120B, 54200A, 54501A, 54502A, 54503A, 54504A, 54520A, 54520C, 54540A, 54540C, 54542A, 54542C, 54600B, 54601A, 54601B, 54602B, 54603B,? 54645A, 54654N, 54710A, 54720A, 54750A, 54825N, E1428,?
- Oven controlled crystal oscillators (OCXOs)
- Pattern generators
- PCM terminal test set
- Phase noise measurement
- Pico ammeters
- Printers 2225
- Plotters 7470A, 7475A?
- Probes
- Protocol analyzers and exercisers.
- Power booster test sets
- Power meters 431A, 431B, 431C, 432A, 435A, 435B, 437B, 438A
- Power splitters
- Power supplies
- Pulse generators
- Q-meters 4342A?
- Q-meter calibration inductors 16470A
- Reflection transmission test set
- Return loss module (optical)
- Relays / switches / switch matrices (optical)
- Relays / switches / switch matrices (RF)
- Resistor standards 42030A?and 42100A
- S-parameter test sets
- Scalar network analyzers
- SCSI bus preprocessor interface E2324A
- Selective level meters 3746A
- Semiconductors
- Semiconductor parameter analyzers 4145A, 4155B, 4156B,
- Signal analyzers
- Signal generators / sweep generators / signal sources / oscillators 200CD, 201B, 209A, 204D,? 608A,? 8165A
- Software
- Source measure units
- Spectrum analyzers 4195A,???
- Switch control units
- SWR meter 415E?
- Time interval? counters
- Time mark generator 226A
- Timing and data state modules
- Torque wrenches
- Transmitter testers
- Trigger modules
- Ultrasound transducers
- Universal bridge? 4260A, 4265A, 4265B?
- Vacuum tube voltmeter 410C
- Vector Impedance Meter 4193A, 4800A, 4815A
- Vector Network Analyzers (VNAs) 4195A,? 8510A, 8510B, 8510C, 8753A, 8753B, 8753C, 8753D, 8753E, 8753ES, 8752ET, 8719A, 8719B, 8719C, 8719D, 8720A, 8720B, 8720C, 8720D, 8720ES, 8722A, 8722B, 8722C, 8722D, 8722ES,
- Vector Network Analyzers (VNA) calibration kits 85032B, 85032E, 85033C, 85033D, 85033E, 85050B, 85050C, 85050D, 85052B, 85052C, 85052D, 85054A, 85054B, 85054D, 85056A
- Vector Network Analyzer (VNA) verification kits
- Vector Signal Analyzer 89650S, 89600S
- Vector voltmeters 8405A, 8508A,
- VXI mainframes 70000B, 70000C
- Waveform and function generators
- Waveguide to waveguide and waveguide to coaxial transitions.
- Wireless 58 OTA chambers
- Wireless channel emulators
- Wireless network emulators
- Wireless communication test sets
?
|
Bricked E1439C after firmware update on 89600
Following a firmware update which showed no errors, my E1439C no longer shows up in the VXI resource manager.
Does anyone happen to have an image of the 28F800 flash chip, insight on how to extract
By
Ed Marciniak
·
#150633
·
|
|
Re: HP Agilent 8753ES VNA repair [Help]
Hello Yves,
Thank you for all the pictures and all the measurements. I understand the board better with your annotations.
The frequency synthesizers and PLL is not the easiest part to understand.
I
By
MattSNE
·
#150632
·
|
|
File /All HP, Agilent and Keysight instruments in folders by part numbers/3000 to 3999/3708 Noise and Interference Test Set/HP 3708A Service_Manual.pdf uploaded
#file-notice
The following items have been added to the Files area of the [email protected] group.
* /All HP, Agilent and Keysight instruments in folders by part numbers/3000 to 3999/3708
By
Group Notification <noreply@...>
·
#150630
·
|
|
Re: 3708A Noise and Interference Test Set - Looking for a Service Manual
Hi Jared,
Just uploaded service manual for 3708A to the 3000 group.
Regards
Gerald
VK3GM
By
Gerald
·
#150629
·
|
|
Re: HP Agilent 8753ES VNA repair [Help]
I took some measurements of the PLL VCO, you can compare. On the
oscilloscope, I put a slight offset for CH1, to be able to better
distinguish the two input signals to the phase detector.
By
Yves Tardif
·
#150628
·
|
|
Re: HP Agilent 8753ES VNA repair [Help]
Hi,
Here is the part of the circuit inside the shield.
It is very similar to the schematic and PCB of an 8753D, but the mixers are
different.
Yves
By
Yves Tardif
·
#150627
·
|
|
Re: HP 54512B (pair) repair
I guess I'm looking for a Delta Electronics 03EB3S-1 (9135-0452) switched
EMI filter (see pic enclosed). It came apart as soon as I tried to see
what's wrong with it.
Thank you in advance for digging
By
Radu Bogdan Dicher
·
#150626
·
|
|
Re: HP 54512B (pair) repair
Two steps forward, one step back (one and a half?).
While other things have been progressing, the power switch stopped working
once I put most of the unit back together. I enclose some pictures,
By
Radu Bogdan Dicher
·
#150625
·
|
|
Re: HP 3403C True RMS Voltmeter display fault
The other one ooks just as weird but is healthy according to the chinese component tester.
Are there guidelines on HP capacitor replacements? Such as caps that never/very rarely fail and those who
By
AArnaud
·
#150624
·
|
|
Re: HP 3403C True RMS Voltmeter display fault
Wow. I have *never* known one of those capacitors to fail. I replace dipped tantalum capacitors all the time, but never one of those!
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
By
Dave McGuire
·
#150623
·
|
|
Re: HP 54512B (pair) repair
Razvan,
Thank you very much, this is very helpful.
I've managed to rig a load - I had a couple of 1ohm/10W Vishay RS10s
(bulletproof, in my experience), and it looks like the -12V rail is MIA
because
By
Radu Bogdan Dicher
·
#150622
·
|
|
Re: HP 3403C True RMS Voltmeter display fault
Hey Guys,
It is indeed a Tantalum capacitor, from the Kemet T110 series. ( https://www.mouser.fr/datasheet/2/447/KEM_T2031_T110_AXIAL_T212-3316949.pdf ) From my research that would be T110B226K015AS.
By
AArnaud
·
#150621
·
|
|
HP8510C CalKit file .CK_ format
Hi there,
I'm trying to generate the calkit file CK_ programmatically instead of punching them in various GUI based CalKit manager.
Basically, I'm doing my homemade open and slot standards and
By
Calvin Guan
·
#150620
·
|
|
Re: HP 54512B (pair) repair
Hi Radu,
I think the PSU in all 545xx series was made by Boschert Inc. and
someone already reverse engineered it. I attached the file.
I hope it helps.
Regards,
Razvan
By
Razvan Popescu
·
#150619
·
|
|
Re: HP 54512B (pair) repair
Going back to my -12V rail issue, the SM advises loading the 5.20V rail
with a 2ohm/25W resistor. The only way I can put something similar together
with what I have at hand is using these dummy loads
By
Radu Bogdan Dicher
·
#150618
·
|
|
Re: HP 54512B (pair) repair
One of the two scopes is completely disassembled - head exploding emoji -
and I have the old battery desoldered after confirming it's fully depleted.
I enclose pics with what I'm using for
By
Radu Bogdan Dicher
·
#150617
·
|
|
Re: E5052A Power On Test (3.3V Bus Supply)
Watching this subject with interest.? Leo, you may want to check out OEWaves, Synergy Microwave, and Holzworth Instrumentation (now part of Maury Microwave) for ultralow PN sources and Rohde &
By
Jim Ford
·
#150616
·
|
|
Re: HP 54512B
I don't believe at this point HP was providing component-level Service
Manuals anymore. I'd love to see one and prove myself wrong, though.
Radu.
By
Radu Bogdan Dicher
·
#150615
·
|
|
Re: HP 8660B/86602B developed output stability problem, getting-started suggestion(s) request
Gary, WB2UAQ --- the advice to make adjustments while the board(s) are enclosed is right on (seeing the solenoid coil on the VCO board helped me see why toroid inductor self shielding property is
By
David Feldman
·
#150614
·
|
|
Re: 3708A Noise and Interference Test Set - Looking for a Service Manual
Someone must have scanned it, as there is a 3708A on feeBay listed with a CD of software & documentation, probably doesn't help much as you don't want another unit to go with
By
factory
·
#150613
·
|