CHECK OUT THE WIKI The purpose of the wiki is mainly to allow you to find information on instruments, either from either
- The model number
- The function(s) listed below. Some instruments have multiple functions - for example, the 4195A is a VNA, spectrum analyzer and an impedance analyzer. Therefore the 4195A is listed in multiple categories
Please also check out HPWiki available here:
- Accessory kits - various types
- AC power analyzers - PA2201A and PA2203A
- AC power supplies 6811C, 6812C, 6813C
- Airlines
- Arbitrary waveform generators M8194A
- Amplifiers?493A, 495A?
- Attenuators (optical) 8156A, 8157A, 8158B, 81566A, 81576A,?
- Attenuators (RF) 8494A
- Attenuator set (500 Ω) 350C
- Attenuator set (600 Ω) 350D
- Attenuator switch driver
- Audio analyzers? 8903A, 8903B, 8903E,? ?
- Base station test sets
- Bit error rate testers (BERTs)
- Cables
- Capacitance meters U1701A, U1701B, 4272A, 4278A, 4279A
- Capacitor Bridge 4270A,
- Capacitor standards 16380A, 16380C,?
- Carrier noise test setsi
- Cesium frequency standards
- Clamp ammeters
- Close field probes
- Crystal Impedance E4915A, E4916A
- Data Acquisition Systems (DAQs)
- DC power analyzers
- DC power supplies 6030A , 6031A , 6032A, 6033A, 6035A, 6131C, 6621A, 6622A, 6623A, 6624A, 6627A, 6255A, 6645A, 6671A, 6672A, 6673A, 6674A, 6675A, 62003A, 62003C, 62003E, 62004A, 62004B, 62004E, 62005A, 62005B, 62005E, 62006A, 62006B, 62006E, 62010A, 62010C, 62010E, 62012A, 62012C, 62012E, 62015A, 62015C, 62015E, 62018A, 62018C, 62018E, 62024A, 62024C, 62024E, 62028A, 62028C, 62028E, 62048A, 62048C, 62048E
- Delay lines
- Detectors
- Device current waveform analyzers
- Digital communications analyzers
- Directional couplers
- Distortion analyzers 330B, 330C, 330D, 331A, 332A, 333A, 334A, 339A, 8903A, 8903B, 8903E,???
- Dynamic measurement DC source
- Electrometers
- Fading simulators
- Femto ammeters
- Filters
- Frequency counters 522B, 5342A 5343A 5352B
- Frequency standards?
- Function Generators ? 3310A,? 8165A,
- GPIB controllers, extenders, cables etc.
- GPS frequency standards
- Harmonic mixers
- High resistance meters 4339B
- High resistance meter fixtures 16008B
- HEV EV Grid Emulators and Test Systems
- In-circuit test systems
- Impedance analyzers 4195A, 4291A, 4291B, 4395A, 4396A, 4396B, 4294A, E4990A, E4991A
- Impedance Analyzer Accessories
- Impedance / Gain Phase analyzer 4194A
- Impedance Meter 4193A,
- Isolators
- LCR meters? U1701A, U1701B, U1731A,? U1731B, U1731C, U1732A, U1732B, U1732C, U1733C, 4191A , 4192A, 4194A, 4195A, E4196A,? 4216A, 4260A, 4261A, 4262A? 4263A, 4263B, 4271B, 4274A, 4275A, 4276A , 4277A, 4284A, 4285A, 4286A, 4287A, 4291A, 4291B, 4294A, 4332A, 4342A, 4395A, 4396A, 4396B, E4980A and E4980AL
- LCR meter calibration devices? 16380A 42030A? 42090A, 42091A and 42100A
- LCR meter accessories
- 2-Terminal BNCs.
- 4-Terminal Pair (BNC connectors)
- Cable extension 16048A, 16048D, 16048E, 16048G, 16048H
- DC current bias accessories 42841A, 42842A, 42842B, 42842C, 42843A
- DC voltage bias accessories 16065A, 16065C,
- Kelvin clips 16089A, 16089B, 16089C,16089E
- Lead Components 16047A,16047B, 16047D, 16047E
- Material 16451B, 16452A
- Probes 42941A
- SMD 16034E, 16034G, 16034H
- 2-port 16096A
- 7 mm (APC7)
- 2-Terminal BNCs.
- LCZ meters? 4276A, 4277A,
- Lightwave clock / data receivers
- Lightwave converter
- Lightwave component analyzer
- Lightwave measurement system mainframes
- Lightwave polarization analyzers 8509B
- Logic analyzers
- Nemo wireless network solutions.
- Noise and interference test set
- Noise figure analyzers
- Noise sources 346A, 346B. 346C ,
- Matching pads (50 ohm to 75 ohm or similar)
- Materials test equipment
- Microwave repeaters
- Microwave downconverters 70427A
- Microwave / THz sources
- Milliammeter 428B
- Milliohm meter
- Mobile communications DC source
- Modular instruments
- AXIe
- Data acquisition (DAQ)
- USB
- PXIe
- Modulation analyzers
- Multimeters 427A, 970A
- Optical attenuators
- Optical heads
- Optical sources
- Optical spectrum analyzers
- Oscilloscopes 120A, 120AR, 120B, 122A, 130A, 130B, 130BR, 130C, 140A, 140B, 141A, 150A, 150AR, 160B, 180A, 180AR, 180CD, 181A, 181AR, 181T, 181TR, 182C, 182T, 183A, 183B, 184A, 184B, 185A, 185B, 1200A, 1200B, 1220A, 1221A, 1703A, 1707A, 1707B, 1710A, 1710B, 1715A, 1722A, 1725A, 1726A, 1740A, 1741A, 1742A, 1743A, 1744A, 1746A, 1980A, 1980B, 5403A, 6000A, 6000L, 16533A, 16534A, 54100A, 5410B, 54100C, 5100D, 54111D, 54120A, 54120B, 54200A, 54501A, 54502A, 54503A, 54504A, 54520A, 54520C, 54540A, 54540C, 54542A, 54542C, 54600B, 54601A, 54601B, 54602B, 54603B,? 54645A, 54654N, 54710A, 54720A, 54750A, 54825N, E1428,?
- Oven controlled crystal oscillators (OCXOs)
- Pattern generators
- PCM terminal test set
- Phase noise measurement
- Pico ammeters
- Printers 2225
- Plotters 7470A, 7475A?
- Probes
- Protocol analyzers and exercisers.
- Power booster test sets
- Power meters 431A, 431B, 431C, 432A, 435A, 435B, 437B, 438A
- Power splitters
- Power supplies
- Pulse generators
- Q-meters 4342A?
- Q-meter calibration inductors 16470A
- Reflection transmission test set
- Return loss module (optical)
- Relays / switches / switch matrices (optical)
- Relays / switches / switch matrices (RF)
- Resistor standards 42030A?and 42100A
- S-parameter test sets
- Scalar network analyzers
- SCSI bus preprocessor interface E2324A
- Selective level meters 3746A
- Semiconductors
- Semiconductor parameter analyzers 4145A, 4155B, 4156B,
- Signal analyzers
- Signal generators / sweep generators / signal sources / oscillators 200CD, 201B, 209A, 204D,? 608A,? 8165A
- Software
- Source measure units
- Spectrum analyzers 4195A,???
- Switch control units
- SWR meter 415E?
- Time interval? counters
- Time mark generator 226A
- Timing and data state modules
- Torque wrenches
- Transmitter testers
- Trigger modules
- Ultrasound transducers
- Universal bridge? 4260A, 4265A, 4265B?
- Vacuum tube voltmeter 410C
- Vector Impedance Meter 4193A, 4800A, 4815A
- Vector Network Analyzers (VNAs) 4195A,? 8510A, 8510B, 8510C, 8753A, 8753B, 8753C, 8753D, 8753E, 8753ES, 8752ET, 8719A, 8719B, 8719C, 8719D, 8720A, 8720B, 8720C, 8720D, 8720ES, 8722A, 8722B, 8722C, 8722D, 8722ES,
- Vector Network Analyzers (VNA) calibration kits 85032B, 85032E, 85033C, 85033D, 85033E, 85050B, 85050C, 85050D, 85052B, 85052C, 85052D, 85054A, 85054B, 85054D, 85056A
- Vector Network Analyzer (VNA) verification kits
- Vector Signal Analyzer 89650S, 89600S
- Vector voltmeters 8405A, 8508A,
- VXI mainframes 70000B, 70000C
- Waveform and function generators
- Waveguide to waveguide and waveguide to coaxial transitions.
- Wireless 58 OTA chambers
- Wireless channel emulators
- Wireless network emulators
- Wireless communication test sets
?
|
Re: HP 54512B (pair) repair
Hi Radu,
I think the PSU in all 545xx series was made by Boschert Inc. and
someone already reverse engineered it. I attached the file.
I hope it helps.
Regards,
Razvan
By
Razvan Popescu
·
#150619
·
|
|
Re: HP 54512B (pair) repair
Going back to my -12V rail issue, the SM advises loading the 5.20V rail
with a 2ohm/25W resistor. The only way I can put something similar together
with what I have at hand is using these dummy loads
By
Radu Bogdan Dicher
·
#150618
·
|
|
Re: HP 54512B (pair) repair
One of the two scopes is completely disassembled - head exploding emoji -
and I have the old battery desoldered after confirming it's fully depleted.
I enclose pics with what I'm using for
By
Radu Bogdan Dicher
·
#150617
·
|
|
Re: E5052A Power On Test (3.3V Bus Supply)
Watching this subject with interest.? Leo, you may want to check out OEWaves, Synergy Microwave, and Holzworth Instrumentation (now part of Maury Microwave) for ultralow PN sources and Rohde &
By
Jim Ford
·
#150616
·
|
|
Re: HP 54512B
I don't believe at this point HP was providing component-level Service
Manuals anymore. I'd love to see one and prove myself wrong, though.
Radu.
By
Radu Bogdan Dicher
·
#150615
·
|
|
Re: HP 8660B/86602B developed output stability problem, getting-started suggestion(s) request
Gary, WB2UAQ --- the advice to make adjustments while the board(s) are enclosed is right on (seeing the solenoid coil on the VCO board helped me see why toroid inductor self shielding property is
By
David Feldman
·
#150614
·
|
|
Re: 3708A Noise and Interference Test Set - Looking for a Service Manual
Someone must have scanned it, as there is a 3708A on feeBay listed with a CD of software & documentation, probably doesn't help much as you don't want another unit to go with
By
factory
·
#150613
·
|
|
Re: Manual for HP 466A amplifier
John, if you’ll share your email address with me, I’ll send the schematic.
Jeremy
N6WFO
[email protected]> wrote:
By
Jeremy Nichols
·
#150612
·
|
|
Re: Manual for HP 466A amplifier
Good point. I’d rather patronize Artek and save us both time and money.
Jeremy
N6WFO
[email protected]> wrote:
By
Jeremy Nichols
·
#150611
·
|
|
Re: Manual for HP 466A amplifier
David,
The Artek manual for 466a is actually 00466-90003.? There's a typo on the website, I'll let Linda know.
It's for serial prefix 226 with backdating for 210, 044, and 019 prefixes.
Ron
By
Ron
·
#150610
·
|
|
Re: Manual for HP 466A amplifier
Dave,
The Artek manual for the HP 466A is for serial number prefix 226.
Ron
By
Ron
·
#150609
·
|
|
3708A Noise and Interference Test Set - Looking for a Service Manual
Hi,
I just pulled my 3708A off the shelf for a bit of a spit polish ready to sell it off and I'm looking for a service manual for the performance test and calibration procedures.
I can't seem to
By
Jared Cabot
·
#150608
·
|
|
Re: HP Agilent 8753ES VNA repair [Help]
Hi,
Starting point VCXO are correct frequency with 40.000MHz.
At TP20 you have a frequency of 39.100MHz, and at the output of divider 40
you get 977.5kHz. This indicates, that the divider by 40
By
Yves Tardif
·
#150607
·
|
|
Re: Service manual scan post processing
wrote:
A very useful amount of cleanup can be done simply by comparing each pixel
on its own to the average of the wide neighbourhood pixels. That works
equally well for text and schematics, since it
By
Tom Gardner
·
#150606
·
|
|
Re: Service manual scan post processing
At the museum, we use ITU-T T.6 (Group 4 FAX), which is lossless and very effective.
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
By
Dave McGuire
·
#150605
·
|
|
Re: Manual for HP 466A amplifier
I don't mind getting it scanned at the museum, but does it still make sense to do that after the revelation that Artek has it available? I hadn't checked before; I had assumed the OP had already
By
Dave McGuire
·
#150604
·
|
|
Re: Manual for HP 466A amplifier
I've got one of those amps and would like the schematic also.
--
John Griessen
By
John Griessen
·
#150603
·
|
|
Re: Service manual scan post processing
While we seem to all agree that JPEG compression is not ideal, there ARE lossless options for TIFF and thus PDF formats.? While yes, storage and networking and processing and scanning time is all
By
Bert
·
#150602
·
|
|
Re: HP 3403C True RMS Voltmeter display fault
Yes, that's why I wanted to see a picture. I've never seen the ball-of-molten-tantalum failure on anything other than a dipped unit.
Seconded.
-Dave
--
Dave McGuire, AK4HZ
New
By
Dave McGuire
·
#150601
·
|
|
Re: HP 3403C True RMS Voltmeter display fault
The manual on the web gives type 150D for C1 & C2 on A7, these are hermetic sealed solid tants, of course they might have been replaced with a bead or the disguised bead in an axial or radial block
By
factory
·
#150600
·
|