CHECK OUT THE WIKI The purpose of the wiki is mainly to allow you to find information on instruments, either from either
- The model number
- The function(s) listed below. Some instruments have multiple functions - for example, the 4195A is a VNA, spectrum analyzer and an impedance analyzer. Therefore the 4195A is listed in multiple categories
Please also check out HPWiki available here:
- Accessory kits - various types
- AC power analyzers - PA2201A and PA2203A
- AC power supplies 6811C, 6812C, 6813C
- Airlines
- Arbitrary waveform generators M8194A
- Amplifiers?493A, 495A?
- Attenuators (optical) 8156A, 8157A, 8158B, 81566A, 81576A,?
- Attenuators (RF) 8494A
- Attenuator set (500 ¦¸) 350C
- Attenuator set (600 ¦¸) 350D
- Attenuator switch driver
- Audio analyzers? 8903A, 8903B, 8903E,? ?
- Base station test sets
- Bit error rate testers (BERTs)
- Cables
- Capacitance meters U1701A, U1701B, 4272A, 4278A, 4279A
- Capacitor Bridge 4270A,
- Capacitor standards 16380A, 16380C,?
- Carrier noise test setsi
- Cesium frequency standards
- Clamp ammeters
- Close field probes
- Crystal Impedance E4915A, E4916A
- Data Acquisition Systems (DAQs)
- DC power analyzers
- DC power supplies 6030A , 6031A , 6032A, 6033A, 6035A, 6131C, 6621A, 6622A, 6623A, 6624A, 6627A, 6255A, 6645A, 6671A, 6672A, 6673A, 6674A, 6675A, 62003A, 62003C, 62003E, 62004A, 62004B, 62004E, 62005A, 62005B, 62005E, 62006A, 62006B, 62006E, 62010A, 62010C, 62010E, 62012A, 62012C, 62012E, 62015A, 62015C, 62015E, 62018A, 62018C, 62018E, 62024A, 62024C, 62024E, 62028A, 62028C, 62028E, 62048A, 62048C, 62048E
- Delay lines
- Detectors
- Device current waveform analyzers
- Digital communications analyzers
- Directional couplers
- Distortion analyzers 330B, 330C, 330D, 331A, 332A, 333A, 334A, 339A, 8903A, 8903B, 8903E,???
- Dynamic measurement DC source
- Electrometers
- Fading simulators
- Femto ammeters
- Filters
- Frequency counters 522B, 5342A 5343A 5352B
- Frequency standards?
- Function Generators ? 3310A,? 8165A,
- GPIB controllers, extenders, cables etc.
- GPS frequency standards
- Harmonic mixers
- High resistance meters 4339B
- High resistance meter fixtures 16008B
- HEV EV Grid Emulators and Test Systems
- In-circuit test systems
- Impedance analyzers 4195A, 4291A, 4291B, 4395A, 4396A, 4396B, 4294A, E4990A, E4991A
- Impedance Analyzer Accessories
- Impedance / Gain Phase analyzer 4194A
- Impedance Meter 4193A,
- Isolators
- LCR meters? U1701A, U1701B, U1731A,? U1731B, U1731C, U1732A, U1732B, U1732C, U1733C, 4191A , 4192A, 4194A, 4195A, E4196A,? 4216A, 4260A, 4261A, 4262A? 4263A, 4263B, 4271B, 4274A, 4275A, 4276A , 4277A, 4284A, 4285A, 4286A, 4287A, 4291A, 4291B, 4294A, 4332A, 4342A, 4395A, 4396A, 4396B, E4980A and E4980AL
- LCR meter calibration devices? 16380A 42030A? 42090A, 42091A and 42100A
- LCR meter accessories
- 2-Terminal BNCs.
- 4-Terminal Pair (BNC connectors)
- Cable extension 16048A, 16048D, 16048E, 16048G, 16048H
- DC current bias accessories 42841A, 42842A, 42842B, 42842C, 42843A
- DC voltage bias accessories 16065A, 16065C,
- Kelvin clips 16089A, 16089B, 16089C,16089E
- Lead Components 16047A,16047B, 16047D, 16047E
- Material 16451B, 16452A
- Probes 42941A
- SMD 16034E, 16034G, 16034H
- 2-port 16096A
- 7 mm (APC7)
- 2-Terminal BNCs.
- LCZ meters? 4276A, 4277A,
- Lightwave clock / data receivers
- Lightwave converter
- Lightwave component analyzer
- Lightwave measurement system mainframes
- Lightwave polarization analyzers 8509B
- Logic analyzers
- Nemo wireless network solutions.
- Noise and interference test set
- Noise figure analyzers
- Noise sources 346A, 346B. 346C ,
- Matching pads (50 ohm to 75 ohm or similar)
- Materials test equipment
- Microwave repeaters
- Microwave downconverters 70427A
- Microwave / THz sources
- Milliammeter 428B
- Milliohm meter
- Mobile communications DC source
- Modular instruments
- AXIe
- Data acquisition (DAQ)
- USB
- PXIe
- Modulation analyzers
- Multimeters 427A, 970A
- Optical attenuators
- Optical heads
- Optical sources
- Optical spectrum analyzers
- Oscilloscopes 120A, 120AR, 120B, 122A, 130A, 130B, 130BR, 130C, 140A, 140B, 141A, 150A, 150AR, 160B, 180A, 180AR, 180CD, 181A, 181AR, 181T, 181TR, 182C, 182T, 183A, 183B, 184A, 184B, 185A, 185B, 1200A, 1200B, 1220A, 1221A, 1703A, 1707A, 1707B, 1710A, 1710B, 1715A, 1722A, 1725A, 1726A, 1740A, 1741A, 1742A, 1743A, 1744A, 1746A, 1980A, 1980B, 5403A, 6000A, 6000L, 16533A, 16534A, 54100A, 5410B, 54100C, 5100D, 54111D, 54120A, 54120B, 54200A, 54501A, 54502A, 54503A, 54504A, 54520A, 54520C, 54540A, 54540C, 54542A, 54542C, 54600B, 54601A, 54601B, 54602B, 54603B,? 54645A, 54654N, 54710A, 54720A, 54750A, 54825N, E1428,?
- Oven controlled crystal oscillators (OCXOs)
- Pattern generators
- PCM terminal test set
- Phase noise measurement
- Pico ammeters
- Printers 2225
- Plotters 7470A, 7475A?
- Probes
- Protocol analyzers and exercisers.
- Power booster test sets
- Power meters 431A, 431B, 431C, 432A, 435A, 435B, 437B, 438A
- Power splitters
- Power supplies
- Pulse generators
- Q-meters 4342A?
- Q-meter calibration inductors 16470A
- Reflection transmission test set
- Return loss module (optical)
- Relays / switches / switch matrices (optical)
- Relays / switches / switch matrices (RF)
- Resistor standards 42030A?and 42100A
- S-parameter test sets
- Scalar network analyzers
- SCSI bus preprocessor interface E2324A
- Selective level meters 3746A
- Semiconductors
- Semiconductor parameter analyzers 4145A, 4155B, 4156B,
- Signal analyzers
- Signal generators / sweep generators / signal sources / oscillators 200CD, 201B, 209A, 204D,? 608A,? 8165A
- Software
- Source measure units
- Spectrum analyzers 4195A,???
- Switch control units
- SWR meter 415E?
- Time interval? counters
- Time mark generator 226A
- Timing and data state modules
- Torque wrenches
- Transmitter testers
- Trigger modules
- Ultrasound transducers
- Universal bridge? 4260A, 4265A, 4265B?
- Vacuum tube voltmeter 410C
- Vector Impedance Meter 4193A, 4800A, 4815A
- Vector Network Analyzers (VNAs) 4195A,? 8510A, 8510B, 8510C, 8753A, 8753B, 8753C, 8753D, 8753E, 8753ES, 8752ET, 8719A, 8719B, 8719C, 8719D, 8720A, 8720B, 8720C, 8720D, 8720ES, 8722A, 8722B, 8722C, 8722D, 8722ES,
- Vector Network Analyzers (VNA) calibration kits 85032B, 85032E, 85033C, 85033D, 85033E, 85050B, 85050C, 85050D, 85052B, 85052C, 85052D, 85054A, 85054B, 85054D, 85056A
- Vector Network Analyzer (VNA) verification kits
- Vector Signal Analyzer 89650S, 89600S
- Vector voltmeters 8405A, 8508A,
- VXI mainframes 70000B, 70000C
- Waveform and function generators
- Waveguide to waveguide and waveguide to coaxial transitions.
- Wireless 58 OTA chambers
- Wireless channel emulators
- Wireless network emulators
- Wireless communication test sets
?
|
HP 3325B repair, help needed with Schottky diode
Hi, I got a HP 3325B, which seems to have seen very little use, no dust inside, and in great shape outside. Giving all different FAILs at the begining. First and easy fo find, two radial tantal 15uF
By
Peter
·
#140634
·
|
|
Re: Help figuring out my 8648C Signal Generator?....
Thanks for the info. :) I ended up buying an earlier manual to suit my serial number (Which doesn't seem to be available online), so one it arrives I'll scan it in and upload it here and there. Maybe
By
Jared Cabot
·
#140633
·
|
|
IF injector card HP 5062-6241
Hello Group, I am searching? this special card to calibrate the IF Section of my HP8593E. Does a GERBER copy of this PCB exist for this card ?, or a photo ? I do Have a copy of one card produced by
By
Guy DAIPRA
·
#140632
·
|
|
Re: HP 8116 doesnt reach 50MHz properly
If I remember correctly, that's about par for the course on these. It's been awhile since I've played with one. I would recommend you let it warm up for about an hour, and then run through the
By
Swiss
·
#140631
·
|
|
HP 8116 doesnt reach 50MHz properly
Hello, i bought an HP8116 in a good condition, working properly except that it can reach about 10MHz and after that the output is attenuated and distorted, in all waweforms. I didnt make the
By
Augusto
·
#140630
·
|
|
Re: Agilent E4406A CPU Board Pulling down the power supply.
On my E4406A I changed all the 100k 1206 SMD resistors on the fan controller board (as one of them had gone open circuit) and this cured an issue with the cooling fan running at full duty all the
By
jmr
·
#140629
·
|
|
Re: HP 8640B Attenuator Repair
I believe that Harley Halvorsen devised those hacks while working on the HP355 family of attenuators. He took Art Fong's design and added the compensation that pushed performance to 1GHz (pretty
By
Tom Lee
·
#140627
·
|
|
Re: HP 8640B Attenuator Repair
*And DO NOT touch or move any of the custom tuning materials such as those white wire "pigtails" or the thin metal strips bent around resistors. Don't move anything, and don't let any bumps occur to
By
Don Brown, N3DEB
·
#140626
·
|
|
Re: HP 8640B Attenuator Repair
Two pics, one of attenuator DC injection points in red and other vernier contacts epoxied.
By
Don Brown, N3DEB
·
#140625
·
|
|
Re: HP 8640B Attenuator Repair
You might research on the web, plenty of discussions. It is not a new concept. Here is one for example: https://maker.pro/forums/threads/microswitch-wetting-current.18605/
By
Don Brown, N3DEB
·
#140624
·
|
|
Re: Agilent E4406A CPU Board Pulling down the power supply.
Does it have any MLCC ceramic caps? Those are also prone to cracking and going short. A $300 thermal camera is really handy to find stuff like this - could be a cap, could be a shorted fet in a
By
Andrew Hakman
·
#140623
·
|
|
Agilent E4406A CPU Board Pulling down the power supply.
Hello, I have got an Agilent E4406A VSA that the PSU is hiccupping due to a supply rail overload. I pulled all the daughter boards and I get down to the CPU board + the front panel and that still
By
Simon WW
·
#140622
·
|
|
89441A firmware M.09.06
Hi, A friend of mine has an 89441A with firmware M.09.06...does anyone have this firmware, because on the Keysight website, the latest downloadable version would be A.09.05.
By
Yves Tardif
·
#140621
·
|
|
Re: HP 8920B
Ok I had to go look at the correct unit this time ? My 8920B options: 001, 004, 010, 013, 051 & 102 Being new to the HP line what is option 55?
By
KB2LMN
·
#140620
·
|
|
Re: 11807E Radio Test Software on PCMCIA Cards for the 8920B
Thanks Robert I just sent payment. What burner do you use I¡¯ve been thinking of getting one but I use windows 11 and i don¡¯t see many that will work? Drew
By
KB2LMN
·
#140619
·
|
|
Re: 11807E Radio Test Software on PCMCIA Cards for the 8920B
I've not seen a copy of the AM test suite. If anyone has a copy I can burn it to a card. Robert.
By
Robert G8RPI
·
#140618
·
|
|
Re: HP8753ES and speed
Thanks for the info Dave! ?We were a computer/TE service company and you wouldn¡¯t (well maybe you would) believe) how hard it was to push proper measures. The IT guru and I were the only computers
By
Stephen Hanselman
·
#140617
·
|
|
Re: HP8753ES and speed
If you decide you need something new and fast, the best bang for your buck is probably copper mountain.? Their TR1300 2-port to 1.3 GHz runs $4K.? Lighthing fast, good interface, and great dynamic
By
Scott Vance
·
#140616
·
|
|
Re: HP 8920B
Oh boy your correct I copied my 2600 info one the wrong page! Oh man I¡¯m sitting home with a 101 fever so I blame the meds!
By
KB2LMN
·
#140615
·
|
|
Re: HP 8920B
those options listed are for a Motorola /GD R26XX Regardless the latest firmware on the 8920B is 6.01
By
John Yelmgren
·
#140614
·
|