¿ªÔÆÌåÓý

Date
Re: Read frequency list from HP 8510C via HP-IB
That usually indicate there is no data (as you found from the error explanation). Are you sure the command is doing what you think it's doing? I've not used the 8510 but with the 8753 you cannot get
By vk2bea · #129349 ·
Re: HP 432A Power Supply
Swapping C1 (100uF) for what I had on hand, 470uF, brought the rails back to somewhere near nominal (+7V is now +7.3V which is out of spec) but it brought the meter back to life so that I can now
By Tony Goodhew · #129348 ·
Re: HP 432A Power Supply
And as soon as I posted this, I went back and checked C1: ( https://imgur.com/iqZEEoF ) And previously I swear it tested correctly but now it is testing at 650nF instead of 100uF - Clearly I did
By Tony Goodhew · #129347 ·
HP 432A Power Supply
Hey All, I'm currently working on fixing up a non-working HP 432A unit - I've identified that there are several issues with the A2 board that I need to address before moving forward: * Power rails
By Tony Goodhew · #129346 ·
HP5340A intermittent or thermal problem
I have this one 5340A microwave counter that just won't work right despite lots of effort. I have four of these altogether, two Nixie style and two LED. Three work beautifully.. The problem one (LED)
By Ed Breya · #129345 ·
Re: HP Z3804A
That's a Motorola Oncore GPS receiver module. -Dave -- Dave McGuire, AK4HZ New Kensington, PA
By Dave McGuire · #129344 ·
Re: HP Z3804A
---------------- Hi Paul, Looking at it again I think you are right, this unit seems to be a prototype based on mix of two existing products. Board on the top is bolted only at 3 places to two bars
By Ozan · #129343 ·
Re: 3458A DMM replaced NVRAMS - cal only or ?
Nothing special in the NVRAMs except the cal data and any stored settings that might have been in them before they died. A fresh cal will remedy the cal constants as long as there are no problems
By Richard Parrish · #129342 ·
Re: HP Semiconductor Analyzers
"Bernd Laengerich" <bernd@...> writes: I think the MP-F52W drive is the 3.5" version? My HP4145B (which contains the 3.5" floppy) was already modified to a HxC, so i don't know what the
By Sven Schnelle · #129341 ·
Re: HP Semiconductor Analyzers
"Sven Schnelle" <svens@...> writes: I've spent way to much time figuring out the problems, so don't laugh :-) The HP4156A just had an open thermal fuse. That one is located below (and glued
By Sven Schnelle · #129340 ·
Re: Hp 8590a eeprom problem.
I have ran the unit all morning without any fail codes. Maybe this thing has sat for a long time and it's getting juiced back up? I think I will go with it as is and if the code comes back I'm gonna
By Richard Cook <richardcook331@...> · #129339 ·
Re: HP Semiconductor Analyzers
I have same issue in tek 2235, failure of the little buggers, same series bourns 3329....not looking fw to getting in there to replace them on the main board input amps. is there anything more
By Ren¨¦e · #129338 ·
Re: HP Z3804A
One additional comment. This is a prerelease widget. Or its one heck of a hack. Notice the GPSDO LEDs are simply drilled through the front cover. No labels. Also and this may have been someone else.
By paulswed · #129337 ·
Re: HP Z3804A
Hello to the group well I'll be darned. Never seen one either. But it surely appears to be a Z380X inside of a distribution amplifier. Very very nice. Thats a great find. If you power it up, it will
By paulswed · #129336 ·
3458A DMM replaced NVRAMS - cal only or ?
Hello group - Recently acquired a 3458 DMM, great condition, but reported errors (I don't remember what they were now...) Dug the battery out of the cal NVRAM and found that it was dead. So replaced
By [email protected] · #129335 ·
Re: HP Z3804A
Thanks guys for the encouragement. However, I have more than enough to keep me busy. I have a very extensive early and rare tube collection, telegraph collection, early wireless from the spark days
By Mike Feher · #129334 ·
Re: Hp 8590a eeprom problem.
If it were me, I would get a ROM reader and read all of the ROMs before using it again while I could, just in case one is failing.
By Matt Harris · #129333 ·
Re: HP Z3804A
----- Hi Hardy, This is a great find, I didn't see it in my searches. I should try it too but the post says equipment reports itself as 59551A. There is quite a bit of information about 59551A,
By Ozan · #129332 ·
Re: OT WTK -Wanted to Know: Reliable sellers, and on-line lists.
Hey Roy! I have some of the rare as hens teeth Wiltron 560 detectors. Let me know if you still need one. Also I have the 8756A scalars with detectors still. I assume you have sweepers??Jeff Kruth In
By Jeff Kruth · #129331 ·
Re: HP Z3804A
My words, my Hungarian brother across the ocean. I am quite old also but ever since I came back to EE, I decided I will never ever stop. Tam With best regards Tam HANNA Enjoy electronics? Join 21k4
By Tam Hanna · #129330 ·