¿ªÔÆÌåÓý

Date
Re: 8640B - No Count
Hello Dave, I have the same problem. I found a self-proclaimed expert, but in the end he stopped communicating; his advice got me nowhere. The main thing I learned was that there have been many
By Brian · #122356 ·
8640B - No Count
I've borrowed a 8640B which as far as high level output works well. The problem is that the counter on both internal and external selection shows all zeros with three decimal points thrown in. There
By Dave Ireland · #122355 ·
Re: 8560E Second Converter
I'm trying to get my head around the LO amp, doubler and tripler circuit of the 8560E Second Converter. Does anyone know to identify the transistor "Bz" and the propriety chip 1GXX-XXX? Dave >
By Dave Ireland · #122354 ·
Re: ESG-DP E4437B Signal Generation Issue
If you are searching for chip replacement then Leo Bodnar is producing drop-in replacement, see: http://www.leobodnar.com/shop/index.php?main_page=product_info&cPath=125_127&products_id=324 -vf- Dne
By Vladimir Filip · #122352 ·
Re: 8560E Second Converter
Askild I have a sig gen and a specan that both go to 3GHz. The test point on the converter is labelled LO test and I assume that this is the 600MHZ but I see nothing on this even though the 600MHz
By Dave Ireland · #122351 ·
Re: Cascaded amplifier for 8673D Watkins Johnson 6203-044 (HP 0955-0215 )
Thank you very much for this information -Yves De : [email protected] <[email protected]> De la part de bigpapak507@... Envoy¨¦ : 10 f¨¦vrier 2022
By Yves Tardif · #122350 ·
Re: ESG-DP E4437B Signal Generation Issue
You are on the right track. The 1GC1-4210 chips tend to deteriorate over time causing the failure mode you described. Your other option is to find a 60019 board and replace it.
By Kenneth Harrison · #122349 ·
Re: HP 8648C keyboard mostly dead
https://www.amazon.com/Circuit-Non-Toxic-Conductive-Electronic-Keyboard/dp/B08T9MKSG5/ref=sr_1_10?keywords=conductive+ink+pen&qid=1644472651&sr=8-10
By Kenneth Harrison · #122348 ·
Re: Cascaded amplifier for 8673D Watkins Johnson 6203-044 (HP 0955-0215 )
By Kenneth Harrison · #122347 ·
Re: HP detector
OK - then ther should be no DC "roll off" Cheers! Bruce Quoting Dave Wright <davewrightsplace@...>:
By Bruce · #122346 ·
Re: HP detector
The 8471A is DC coupled. The input termination resistor is connected between the diode anode and case. The output capacitor is connected between the diode cathode and the case. _Dave
By Dave Wright · #122345 ·
Re: My Agilent MSOX2024A hangs at boot. Will Keysight still repair it at no charge?
Here's the response I got from Keysight today: ---------------------------------------------------------------------------------------------------------------------------------------------------------
By Stan · #122344 ·
Re: 54717A Calibrator
Can you post pictures from the bottom also ? Would be also nice if you would take out this board, and make photos with different angles, it's a lot of reflections there.? Best RegardsArkadiusz W
By Arkadiusz Gibes · #122343 ·
Re: 54717A Calibrator
It has eeprom, it's the hn58c65. W ?roda, 9 lutego 2022, 21:04:19 CET, <boddax@...> napisa?(-a): here the pics.. https://ibb.co/6RdDLj9 https://ibb.co/kB7Sxbx
By Arkadiusz Gibes · #122342 ·
Re: 54717A Calibrator
No i dont have disk ..ill post pics soon , maybe yes i dont know much about 54712A
By boddax@... · #122341 ·
Re: 54717A Calibrator
here the pics.. https://ibb.co/6RdDLj9 https://ibb.co/kB7Sxbx https://i.ibb.co/r7FcGpk/20220209-204320.jpg https://i.ibb.co/HKGMzSW/20220209-204400-004.jpg https://postimg.cc/yk8fwRss (
By boddax@... · #122340 ·
Re: HP detector
Is the detector DC coupled or is there a blocking cap ? Cheers! Bruce Quoting Dave Wright <davewrightsplace@...>:
By Bruce · #122339 ·
Re: 54717A Calibrator
I didn't know that it has no eeprom. It would be nice to have? some detailed pictures of trigger plugin from inside maybe that would help. About eeprom content i menaged do changed it so it's
By Arkadiusz Gibes · #122338 ·
Re: HP detector
The HP 8471A OEM diode is 1N831, and there are some on eBay. I have two on the way now. Left to right in the photo is the input termination resistor, 50 Ohms, some sort of film deposited on the disk
By Dave Wright · #122337 ·
Re: 54717A Calibrator
Arkadiusz Gibes? , I own the trigger you mention look very similar to the calibrator but has no eprom inside my plan was to modi the trigger ..easy to do but cal unit has the eeprom and the unit fail
By boddax@... · #122336 ·