开云体育

I need a 10E156 in plcc, can't find it anywhere. Would any of you have one to spare ? Or know where to buy ? Mny tks. Luis Cupido. ct1dmk.

I have just recently began having trouble with my 8921. What is happening is this:When in duplex mode I get the warning "Duplex Out Overpower" And it suggests changing ports and or lowering level. I

I'm not aware that Agilent every produced the schematics for the 8648x series. Richard Parrish From: hp_agilent_equipment@... [mailto:hp_agilent_equipment@...] On Behalf Of

Victor, ? You don't suppose they had a little training in economics do you?? Apply the principles of supply & demand. ? Jon ? To: hp_agilent_equipment@... Sent: Friday, September 9,

What's the story with LittleDiode? I see a lot of current stock items that they price at 3X to 4X the usual rate. Do they operate like a parts broker and wait for the few big scores from desperate

Hey Steve, ? Is that SJ1891 a darlington?? If not .. does that darlington pair drive the SJ's?? (16) 2N3771 / 3772's work really well as shunts if balanced with negative feedback and driven

I know its not HP / Agilent, but Anybody ever own / work on / repair one of these electronoc loads? I recently picked on up (with manual) and I would like to get it going & useful. One of the problem

Thanks Ron, will do. Marco

Marco Cricklewood Electronics in the UK advertise the 2N5583 at ?15. http://www.cricklewoodelectronics.com/Cricklewood/search.php?mode=search&page=1 Phone or email to check stock to be sure of

I need to purchase some 2N5583 (output stage of 33120A). The usual dealers (RS,Farnell,Mouser,Digicom) have nothing. It is available on ebay from Littlediode at the bargain price of GBP 23.79 a

But the 3325A/B has an exceptional fractionary synthesizer allowing mHz frequency resolution. It

Hi all. I have both the 3225A and the 3324A. The 3324A has flexible sweep modes, multi interval, linear or log sweeps with multi interval markers. It also has verifiable phase control Mine has the .05

I think it's fairly available. If no one has a better copy, I can try to find my copy. I don't use the 68000 myself. The easiest wa

Dave and all, Thanks for everyone's help. I was refering to Option 002 on the plug in I was after. I have an 8350B and manual but wound up with an 8350A. Like most of the folks on this list, I don't

I am very new to the HP 16500 logic analysis family. I have a copy of what I believe to be HP's inverse assembler software for the HP 16500C logic analyzer family. It is the same software version I

I am a long time lurker and eavesdropper on this list and a once-in-a-while poster. This is a very informative and knowledgeable group with some really great talent. I have learned a ton of stuff over

Can anyone here supply schematics for the HP 8648C signal generator or tell me where I can get them? I have the so-called Operation and Service Guide--all 464 pages and not a schematic in sight. --

John, the data cable uses 25 of the 50 possible wires, so construction isn't a big deal. 4 of the 5 RF type connectors are used in the interconnect. Only two carry RF; the other two carry sweep

Let me amplify a bit: You describe a "buzz". That implies non-linearity. A transformer hums. An SCR phase control can make much more of a buzzing sound. I don't know if there is one, but such wires

$239 + $16 - ebay #110738281930 - from Israel, but the seller has good feedback. The original HP cables work for the 8566/8567 as well so you can broaden your search - just make sure the coax cable