开云体育

Hi Dan, i've tried to mail you off list using address in this msg... but no reply, till now. I have an 8410C + 8414A, but no Smith Charts for 8414A. Tried to find some, no luck... So, please let me

They are on eBay sometimes, but certainly not cheap, from an outfit in Hong Kong. -John ==============

Hello Group I miss a Yig oscillator for a HP8753C part number 5086-7473. I would like to se if one has either a source assembly A3 or just the Yig. I hope anyone can help me best regards Peter OZ1LPR

Turns out it was relay K300 which is marked incorrectly on the schematic as K201. It is switched by signal *EXT which is output from the U300 latch.

Hi Folks, Me again, quick question if I may, is the PSU Module used in the HP8591A the same as what's used in a HP8593A, as the PSU for the 8593A is an HP P/N 0950-1977 or MicroEnergy P/N 10-0060, if

Okay Steve, ? Thanks for the reply, I was just drawing a visual on how that device was configured.? Good luck?on your journey. ? Jon To: hp_agilent_equipment@... Sent: Monday,

Hello Jon, No just for clarification, the Darlington pair is comprised of the 2N5298 paired up with the mystery device SJ1891; now identified as the 2N5886. Otherwise you got it pretty much correct;

Hello all, I have on my bench a 8112A that is getting E14 error on power-up. Taking a closer look, I have found that it works perfectly until LEE or TREE is set to 100nS at which point the generator

Oh, yes. It has 1 mHz resolution on all the band, 0.001 Hz to 21 MHz on the front panel, and 21 to 61 MHz from the back panel. So, I may generate a signal at 10,000,000.001 Hz, and calibrate a

Hi all...Found a small supply of original, NOS Smith Charts for the 8414A...Priority would be to those who will archive them, then to those who need them...Contact me off list.... 08414-0010

Just checking the specs for the 3324A. Sine: 1Mhz-21MHz Resolution: 1mHz up to 1MHz 100mHz from 1MHz to 21 MHz Is the 3325A better resolution that that? If so, that's very impressive! --- 73 Eugene

Not in the EU, but ... http://www.weirdstuff.com/cgi-bin/item/90003 73 & Good afternoon, Marv WC6W http://qsl.net/wc6w/

Mark, Thanks for the offer but I'm afraid that the probe you have will not help me. It has way too many pins. The M68000 processor I am working with is a 62 pin PLCC package. There is an HP

One way or another, you're going to wind up opening the meter, even if it is sealed. So go ahead--maybe you'll find a broken wire that could be soldered back. Another thought: a lot of meters,

I just helped a friend of mine obtain a Hickok TV-2 tube tester. It seems the meter for the trans-conductance has an open coil. Can these be repaired? I think the meter case is sealed. If not does

Wim I have both an original manual available or I can have a scan in about 3 days...contact me off list for details 73 Dave NR1DX Artekmedia -- Dave& Lynn Henderson Manuals@...

I assume you have tried: HP-Agilent BAMA ArtekMedia If you can't find the doc you need, please sent it to me before you scrap it. I'll pay postage. Best, -John ==============

Hello, Just got a DA converter hp 59303a, which has a problem in the analog part, gives only -13 volt on the output. The reference of 10 volt on the board is oke, so the problem seems to be around the

You could build a servicable one pretty easily using a couple of Rs, C, and a diode inside a short length of hobby shop brass tubing. Just keep the leads short. -John ============

hi tom, would you mind finding out how much it would cost you to ship the power supply over to me please. if there isnt much saveing then i might as well save you the hastle and just order it direct