开云体育

I am wanting to replace some of the electrolytic filter caps in my HP 141T display section. One of the caps is a two section twist-lok. I can't seem to find a 2-section replacement. What are my

Helloo all, how "in store" can you check out a HP 428B Clip-On DC Milliammeter without the probe? Any caveats, or things to watch for? Thanks Dave

Hello again Kevin. I (think?) I sent this to myself instead of you so I will attempt to send this back to you. Thanks for your time and have a great day. Respectfully, Robert

Hello Kevin. This is Robert. Thank you for your e-mail. Currently I don't have a manual for the HP 1710A scope, however I run accross (alot) of test gear and many times there are also manuals that

Hi Everyone, I have just joined your group as I have started to repair HP scopes and other similar equipment. I am also a member of the Tektronix group so I hope this is not held against

JM If I recall there are two xtal oscillators. They are both designed along the same lines. Check the output on a good digital scope with at least 500 mhz bw. You will see where the problems

I recently acquired an HP 3457A. The instrument seems to work, but I get error "9 NOT CAL'D" when switching to ohm and freq functions and on completion of the self test, even though it says "SELF

Hi, Did you try : http://www.logsa.army.mil/etms/find_etm.cfm ? Type HEWLETT in field "TM Title Text" to find HP Manuals. Hope this helps, Itloiiw wrote:

David, I have the HP 1740A operator's manual, at: http://www.fullnet.com/u/tomg/manuals.htm It's probably also available on line, somewhere, to download. Regards, Tom Gootee --------------

Hi All! I have recently acquired an HP 1740A dual-beam oscilloscope - but alas without a User Manual. I would appreciate help in acquiring a manual from this expert Yahoo group. Best

Which oscillator? -- jm

I found similar problems with my 8656A. I replaced all electrolytic caps. I also replaced the osc. I believe it's a FET, try Sphere in B.C. they had some. I still have one extra. It's not as

They all do that. The 8656A has a lot of close-in phase noise. Not clean enough for any SSB work that requires an extremely stable reference. -- john KE5FX

I have a HP8656A signal generator. Works fine for FM and AM. However, when using it to test a SSB receiver there is a pronounced "warble" in the tone and it is serious enough to affect the

Hi Dave, Thank you very much for your help. I am going to download the free trial. May be that?s enough for my job. Regards, <emailw8nf@y...> wrote:

Carlos, I just went to the Agilent website. I was shocked to see that Benchlink for spectrum analyzers appears to sell for $310!!! Agilent did not write this software themselves, but sourced it

Hi, I would like very much to transfer to my PC data from my Spectrum Analyzer. Someone told me I need this software to do the job: "E4444A BenchLink Spectrum Analyzer Connectivity Software". Would

<walter2@s...> wrote: Hi Walter, its a 2N3669. HP 1884-0019: VRRM 200V VDRM 600V IT (RMS) 12.5A ITSM 200A PG 0.5W PGM 40W VT (MIN)200V IGT MAX 40.0m VGT MAX 1.5V VTM MAX 1.8V Outline Drawing 2

OK, Richard, I'll see what I can do. I'll need a couple of days to dig these up out of (shudder!) "The Storage". I don't maintain the scope in-cal any more and the manuals are in the dead file. Did

<fwolsen@e...> wrote: Hi Fred, OK,how about the HV section ? What has happened, is similar to "blooming" in a TV set. I haven't removed the side panels, yet. Focus,etc, has no effect. But, the problem