¿ªÔÆÌåÓý

Re: HP 3335A Repair


 

Larry,
You're right?and my apologies again to the members and moderators. I will approach this differently?next time (which is how I typically do it).
Radu.?

On Sat, Sep 17, 2022 at 2:26 PM Larry McDavid <lmcdavid@...> wrote:
I got them all but, Radu, you really should edit photos for image size
before sending them as Group emails. Remember that email attachments
incur about 30% overhead! Each email was 21 MB big. There are lots of
free image editors around...

Best wishes,

Larry McDavid W6FUB
Anaheim, California (SE of Los Angeles, near Disneyland)

On 9/17/2022 2:19 PM, Radu Bogdan Dicher wrote:
> Apologies if my attachments have been too large for some inboxes. Could
> anyone please confirm the message was received by at least some people
> and by the forum?
> Thank?you,
> Radu.
>
> On Sat, Sep 17, 2022, 2:09 PM Radu Bogdan Dicher via
> <> <vondicher=[email protected]
> <mailto:[email protected]>> wrote:
>
>? ? ?By "top PCB" I mean the one on the right side as one faces the rear
>? ? ?of the unit (A15), and "bottom PCB" the left side one (which is also
>? ? ?the one with the large PS caps) - A14.
>? ? ?Radu.
>
>? ? ?On Sat, Sep 17, 2022 at 1:59 PM Radu Bogdan Dicher via
>? ? ?<> <vondicher=[email protected]
>? ? ?<mailto:[email protected]>> wrote:
>
>? ? ? ? ?Still working on the PS disassembly procedure.
>? ? ? ? ?I removed two screws at the back:
>? ? ? ? ?image.png
>? ? ? ? ?And the top PCB started wiggling a bit, though it is still is
>? ? ? ? ?attached with two inaccessible screws:
>? ? ? ? ?image.png
>? ? ? ? ?As these are facing the row of shielded modules that goes from
>? ? ? ? ?front to back of unit.
>? ? ? ? ?image.png
>? ? ? ? ?I surely hope I don't have to hollow the entire unit just to get
>? ? ? ? ?the PS out?...
>? ? ? ? ?If I try from the other side, the side panel is also obstructing
>? ? ? ? ?access to a couple of screws:
>? ? ? ? ?image.png
>? ? ? ? ?The same screws seen from the inside of the unit:
>? ? ? ? ?image.png
>? ? ? ? ?The bottom PCB seems to be used as a card into a header:
>? ? ? ? ?image.png
>? ? ? ? ?So I assume this one may detach a little easier, though the caps
>? ? ? ? ?are placed in their own sleeves. Are those sleeves just sliding out?
>? ? ? ? ?Thank you for your insights!
>? ? ? ? ?Radu.
>
>
>? ? ? ? ?On Sat, Sep 17, 2022 at 1:43 PM Radu Dicher <vondicher@...
>? ? ? ? ?<mailto:vondicher@...>> wrote:
>
>? ? ? ? ? ? ?Well, further schematic errors... (thanks a ton to Ozan who
>? ? ? ? ? ? ?straightened me on this one). C2 and C4, as they "stand" on
>? ? ? ? ? ? ?the schematic, are opposite in polarity. The schematic is
>? ? ? ? ? ? ?incorrect:
>? ? ? ? ? ? ?image.png
>? ? ? ? ? ? ?C2 should be reversed from what the schematic says (positive
>? ? ? ? ? ? ?on bottom).
>? ? ? ? ? ? ?Hope this helps someone down the line.
>? ? ? ? ? ? ?Radu.
>
>? ? ? ? ? ? ?On Sat, Sep 17, 2022 at 12:03 PM Patricio A. Greco via
>? ? ? ? ? ? ? <>
>? ? ? ? ? ? ?<patricio_greco=[email protected] <mailto:[email protected]>>
>? ? ? ? ? ? ?wrote:
>
>? ? ? ? ? ? ? ? ?I¡¯m sorry I¡¯ve a little mixed the capacitor reference
>? ? ? ? ? ? ? ? ?numbers . You have >= 20v on C100 / 200 ? This is the
>? ? ? ? ? ? ? ? ?start. I had similar problems with my power supply. So I
>? ? ? ? ? ? ? ? ?decided to remove it and test the components one by one.
>? ? ? ? ? ? ? ? ?I recommend this procedure because it¡¯s dangerous to
>? ? ? ? ? ? ? ? ?have the rest of instrument conected to a faulty power
>? ? ? ? ? ? ? ? ?supply. There are 30% less now but can go up , no much
>? ? ? ? ? ? ? ? ?because it¡¯s has a great design but in my view keeps
>? ? ? ? ? ? ? ? ?being uncomfortable .
>
>? ? ? ? ? ? ? ? ?Is not difficult to remove the complete module .
>
>? ? ? ? ? ? ? ? ?Regards
>
>? ? ? ? ? ? ? ? ?Ing. Patricio A. Greco
>? ? ? ? ? ? ? ? ?Taller Aeron¨¢utico de Reparaci¨®n 1B-349
>? ? ? ? ? ? ? ? ?Organizaci¨®n de Mantenimiento Aeron¨¢utico de la Defensa
>? ? ? ? ? ? ? ? ?OMAD-001
>? ? ? ? ? ? ? ? ?Gral. Mart¨ªn Rodr¨ªguez 2159
>? ? ? ? ? ? ? ? ?San Miguel (1663)
>? ? ? ? ? ? ? ? ?Buenos Aires
>? ? ? ? ? ? ? ? ?T: +5411-4455-2557 <tel:+5411-4455-2557>
>? ? ? ? ? ? ? ? ?F: +5411-4032-0072 <tel:+5411-4032-0072>
>? ? ? ? ? ? ? ? ?
>? ? ? ? ? ? ? ? ?<>
>
>>? ? ? ? ? ? ? ? ?On 17 Sep 2022, at 15:21, Radu Bogdan Dicher
>>? ? ? ? ? ? ? ? ?<vondicher@... <mailto:vondicher@...>> wrote:
>>
>>? ? ? ? ? ? ? ? ??
>>? ? ? ? ? ? ? ? ?To prevent any confusion, when I said I am reading 40V
>>? ? ? ? ? ? ? ? ?instead of 55V, this is between the negative legs of
>>? ? ? ? ? ? ? ? ?C2 and C4. Not at either one's legs vs ground, or over
>>? ? ? ? ? ? ? ? ?either one.
>>? ? ? ? ? ? ? ? ?This replicates step 2 from Service Group 8 (p.8-F-1).
>>? ? ? ? ? ? ? ? ?There was no way to connect to what they're calling
>>? ? ? ? ? ? ? ? ?for ("the junction of R1 and CR2 and R2 and CR4").
>>? ? ? ? ? ? ? ? ?Hopefully this helps with the clarity of my empirical
>>? ? ? ? ? ? ? ? ?data.
>>? ? ? ? ? ? ? ? ?Radu.
>>
>>? ? ? ? ? ? ? ? ?On Sat, Sep 17, 2022 at 11:13 AM Radu Bogdan Dicher
>>? ? ? ? ? ? ? ? ?via <>
>>? ? ? ? ? ? ? ? ?<vondicher=[email protected]
>>? ? ? ? ? ? ? ? ?<mailto:[email protected]>> wrote:
>>
>>? ? ? ? ? ? ? ? ? ? ?Hi Patricio,
>>? ? ? ? ? ? ? ? ? ? ?One overall conclusion is that all rails are down
>>? ? ? ? ? ? ? ? ? ? ?by about 30% (mind you, the same rate). Given
>>? ? ? ? ? ? ? ? ? ? ?they're all referenced to the +15V rail, the
>>? ? ? ? ? ? ? ? ? ? ?running assumption is that something's wrong with
>>? ? ? ? ? ? ? ? ? ? ?the?+15V regulator.
>>? ? ? ? ? ? ? ? ? ? ?I see less than 1.8V over C2.
>>? ? ? ? ? ? ? ? ? ? ?Radu.
>>
>>? ? ? ? ? ? ? ? ? ? ?On Sat, Sep 17, 2022 at 10:15 AM Patricio A. Greco
>>? ? ? ? ? ? ? ? ? ? ?via <>
>>? ? ? ? ? ? ? ? ? ? ?<patricio_greco=[email protected]
>>? ? ? ? ? ? ? ? ? ? ?<mailto:[email protected]>> wrote:
>>
>>? ? ? ? ? ? ? ? ? ? ? ? ?Please note that the voltage outputs are : + -
>>? ? ? ? ? ? ? ? ? ? ? ? ?15 vdc , 5 vdc and -5.2 Vdc ¡­ If C2 has > 40
>>? ? ? ? ? ? ? ? ? ? ? ? ?Vdc is ok. Please take a look to power supply
>>? ? ? ? ? ? ? ? ? ? ? ? ?schematic ¡­
>>
>>? ? ? ? ? ? ? ? ? ? ? ? ?image0.jpeg
>>
>>? ? ? ? ? ? ? ? ? ? ? ? ?Ing. Patricio A. Greco
>>? ? ? ? ? ? ? ? ? ? ? ? ?Taller Aeron¨¢utico de Reparaci¨®n 1B-349
>>? ? ? ? ? ? ? ? ? ? ? ? ?Organizaci¨®n de Mantenimiento Aeron¨¢utico de
>>? ? ? ? ? ? ? ? ? ? ? ? ?la Defensa OMAD-001
>>? ? ? ? ? ? ? ? ? ? ? ? ?Gral. Mart¨ªn Rodr¨ªguez 2159
>>? ? ? ? ? ? ? ? ? ? ? ? ?San Miguel (1663)
>>? ? ? ? ? ? ? ? ? ? ? ? ?Buenos Aires
>>? ? ? ? ? ? ? ? ? ? ? ? ?T: +5411-4455-2557 <tel:+5411-4455-2557>
>>? ? ? ? ? ? ? ? ? ? ? ? ?F: +5411-4032-0072 <tel:+5411-4032-0072>
>>? ? ? ? ? ? ? ? ? ? ? ? ?
>>? ? ? ? ? ? ? ? ? ? ? ? ?<>
>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ?On 17 Sep 2022, at 12:39, Radu Bogdan Dicher
>>>? ? ? ? ? ? ? ? ? ? ? ? ?<vondicher@...
>>>? ? ? ? ? ? ? ? ? ? ? ? ?<mailto:vondicher@...>> wrote:
>>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ??
>>>? ? ? ? ? ? ? ? ? ? ? ? ?I whipped out my longest probes - an inspired
>>>? ? ? ? ? ? ? ? ? ? ? ? ?overstock purchase from maybe Anchor near
>>>? ? ? ? ? ? ? ? ? ? ? ? ?SF?... - (pictures added to album, hoping
>>>? ? ? ? ? ? ? ? ? ? ? ? ?they give some ideas to others get that deep
>>>? ? ? ? ? ? ? ? ? ? ? ? ?inside the belly of this unit) - and I am
>>>? ? ? ? ? ? ? ? ? ? ? ? ?getting 40V at the minus leg of C2 and C4 (my
>>>? ? ? ? ? ? ? ? ? ? ? ? ?probing points), vs. an expected 55V.
>>>? ? ? ? ? ? ? ? ? ? ? ? ?Interestingly, as soon as I power off the
>>>? ? ? ? ? ? ? ? ? ? ? ? ?unit, the voltage there jumps up to about
>>>? ? ? ? ? ? ? ? ? ? ? ? ?45V, and even raises a bit more as the unit
>>>? ? ? ? ? ? ? ? ? ? ? ? ?is standing powered off (5 minutes later I
>>>? ? ? ? ? ? ? ? ? ? ? ? ?measure about 47V...).
>>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ?Continuing my investigation.
>>>? ? ? ? ? ? ? ? ? ? ? ? ?Radu.
>>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ?On Sat, Sep 17, 2022 at 6:01 AM Radu Bogdan
>>>? ? ? ? ? ? ? ? ? ? ? ? ?Dicher via <>
>>>? ? ? ? ? ? ? ? ? ? ? ? ?<vondicher=[email protected]
>>>? ? ? ? ? ? ? ? ? ? ? ? ?<mailto:[email protected]>> wrote:
>>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Thank you all for sharing your thoughts.
>>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?I tried sending some pictures yesterday
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?by replying to the email chain with
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?attachments, but in doing so I exceeded
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?the max size. I created a photo
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?album?instead:
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?/g/HP-Agilent-Keysight-equipment/album?id=278590
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?</g/HP-Agilent-Keysight-equipment/album?id=278590>.
>>>
>>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Will keep investigating this morning. I'm
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?surprised?to not find some paragraphs on
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?removing (each) modules in their
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?troubleshooting sections (typically with
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?images), which I expect from an HP manual
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?(particularly component-level). Anyway,
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?that concludes my whining and will go
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?ahead and dig in there more vigorously.
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Radu.
>>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?On Sat, Sep 17, 2022 at 5:25 AM Patricio
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?A. Greco via <>
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?<patricio_greco=[email protected]
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ?<mailto:[email protected]>> wrote:
>>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?I have a HP3335A. I started to
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?experiment problems as cpu freeze and
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?leveling errors and I found
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?microscopic cracks on power supply
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?board also I removed the transistors
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?and found an anormal slope on
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?characteristic curves (this is
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?thermal deterioration). Replaced the
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?transistors and re-soldered the
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?complete board, Also I removed the
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?capacitors for test , these was ok .
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Cleaned the contacts and mounted
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?again. After that work, instrument
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?started to work like never. It??s
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?very very flat, let me show you the
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?results. I attached the response
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?curves I measured. X Avis is
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?logarithmic starting @1 MHz , and Y
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Axis is in dB relative to 1 MHz. I
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?used 3 different methods to measure.
>>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Regards,
>>>
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Ing. Patricio A. Greco
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Taller Aeron¨¢utico de Reparaci¨®n 1B-349
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Organizaci¨®n de
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Mantenimiento?Aeron¨¢utico de la
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Defensa OMAD-001
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Laboratorio de Calibraci¨®n ISO
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?17025?AREA: RF/MW
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Gral. Mart¨ªn Rodr¨ªguez 2159
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?San Miguel (1663)
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Buenos Aires
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?T: +5411-4455-2557
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?F: +5411-4032-0072
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?<>
>>>
>>>
>>>
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?On 17 Sep 2022, at 08:01, Harold
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Foster <halfoster@...
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?<mailto:halfoster@...>> wrote:
>>>>
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Taking the assemblies loose is
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?almost essential to troubleshooting
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?the supply boards, but *very
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?important:* You have to install a
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?jumper to reconnect the ground - the
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?boards are grounded through one of
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?the brackets (the one to the bottom
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?of the chassis if I remember
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?correctly) and will be disconnected
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?when it it taken loose.
>>>>
>>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Hal
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?WhatsApp Image 2022-07-21 at 3.19.42
>>>? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PM.jpeg
>>>
>





Join [email protected] to automatically receive all group messages.