开云体育

Dave, I bought 5 ADE-25MH from huyai-components on Sept. 22, 2019 @ EUR 4.29 and they work fine. Tried 2 of them so far: one working in the TinySA and one in a modified SPECAN. -- Joerg, ex-DB2OO

The mixers that you got, were those from huayi-components seller on ebay?

Hi group I have finally got round to building the Tiny-SA this week. My version uses B3555 filters, kindly supplied by Tony G4WIF, and I am using an ESP32 as the processor (another processor with

Joerg, You have to ensure the inductors can not "see" each other otherwise the magnetic fields will destroy the stopband. At least put consecutive inductors on 90 degrees angle The SMD capacitors

Touch interface working! Not all functions done yet but already much nicer to use -- HBTE Files section: /g/HBTE/files Erik, PD0EK

I have built a 9th order Bessel 300MHz lowpass, according to the parameters from https://rf-tools.com/lc-filter/. ( https://rf-tools.com/lc-filter/ ) I set the minimum capacity to 2.2pF and minimum

As the code it multi threaded things get "out of order" in the logging. The logging is wrong, should be {} -- HBTE Files section: /g/HBTE/files Erik, PD0EK

It should be at the front. The 350MHz filter has not been tested, its an elliptical filter and maybe too critical in component values. -- HBTE Files section: /g/HBTE/files Erik, PD0EK

Erik, You originally put the attenuator at the very front end.? Your latest schematic shows it after the low pass filter. Which do you reccommend? Also, I see you redesigned the filter for 350MHz?

I'm pretty far along with the Jan 17 tinySA.ino file. Will probably stick with it unless there's a significant reason to go with newer code. Hope to eventually be using the native RPi display, not the

Erik, If that is not from the Jan 17 tinySA.ino currently in the files section, could you post the code it corresponds to? Though I may have all I need if the Jan 17 tinySA.ino file? was working well

Erik, I really appreciate, that you seem to read my mind: I am eagerly looking for the code for the ILI9341 user interface. I have two of those: one with parallel interface and the other with SPI

Excellent, that's perfect!!! Jerry

As requested, inverse order (latest on top), generated by enabling the logging in tinySA.exe Scan of 100 points from 0 till 100MHz Send by tinySA: "<<" Received by tinySA: ">> "__" means CR/LF as

Erik, I did find your list, it was a big help in getting a handle on tinySA.ino Have you verified that the current MSWindows package does not use any commands other than listed? Better yet, could you

Yes good. That controller is used on many displays from 2.8 to 7”… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ Owner - Operator Big Signal Ranch – K9ZC Staunton,

Yes, The tinySA.ino is derived from my generic VNA/SA sweeper that includes the commands for various tracking generators. Inside the build instructions (see file area) there is a list of used commands

Looks good! That 2.8" screen makes it a good complement to a nanoVNA. And the nanoVNA is certainly popular. Though the the newer nanoVNA versions are going to a bigger screen. I'd prefer to have both

The first display was really tiny, the TFT 2.8" ILI9341 with touch is still cheap but more eye friendly and not too difficult to interface. With the touch I can drop the rotary and have a clean setup.

Don't know a lot about the Si4432, but on the Si5351 these can improve spurs and noise: Shut down the other two outputs or there will be crosstalk. Load the single remaining output lightly,