开云体育

In that case good luck but suggest you also look at Jay's website where he provides a step by step of creating MVS rom scratch and after all it is only mil time used, although some of yours

Thank you Vince, Wally contacted me. I am aware of TK5 and its awesome work, but my goal is to build my own system and learn by doing that rather than get it pre-assembled, part of the enjoyment is

Try going to : www.prince-webdesign.nl/tk5 Current version although there will be an update next month all things willing and any changes made to any current version will not be affected by any

I would like to obtain a copy for my home usage, of Wally’s ISPF clone, I tried a direct e-mail to Wally but possibly I have his address wrong, I have not heard back so am trying here. My reading

In my case, the second OSA would connect to an entirely different network, on a different Ethernet switch. How would that be configured? Regards, David

Jake (zpmain) wrote: Hi Jake! I'm not sure what you mean by "secondary OSA" (did you mean: "a second OSA?", or "another OSA?"), but yes, that's all you need to do. Just like any other device

Hello Right now I am using the below statement to define one OSA devices 0400.3 OSA CHPID F0 iface 192.168.1.2 ipaddr 192.168.1.5 netmask 255.255.255.0 If i want second OSA devices defined then how

Does it actually work? I ran the procedure as a regular job under HERC01 and IEBGENER returned RC=12, complaining that SYSUT1 did not have BLKSIZE/LRECL specified. As my SYS1.DUMP00 is (already?)

> > and for TK5 you have: > > RFEVIEW ?SYS1.PROCLIB(CLRDMP) - 1.00 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?COLUMNS > 1 72 > Command ===> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

One other thing of note: An S522 ABEND is *exceedingly* uncommon for anything but a TSO session, where it's issued if the session has been idle too long. Anywhere else, and it's almost certainly

So this is a TK4- vs. TK5 thing, for those of you just tuning in. For TK4- you have: RFEVIEW ?SYS2.PROCLIB(CLEARDMP) ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? COLUMNS 1 72 COMMAND ===> ?

Google AI says: The S522 abend is not a typical job time exceeded error, it's a *job wait time exceeded*. That is to say, the time allocated to wait in an SVC wait state was exceeded. So I looked to

Why's it trying to take an SVC dump on a 522? For that matter, what's NJE38 waiting on for 30 minutes that it takes a 522 in the first place? Got a dataset conflict or something? Your dump datasets

I seem to be having a "similar" problem, at least as far as SYS1.DUMP being full. For TK4- I get the following: - ? ? ? ? ? S CLRDMP,DUMP=DUMP00 STC ?778 ?$HASP100 CLRDMP ? ON STCINRDR STC

Hi Ian, Looks like the connectivity is stable now, for the past two days. I shall let you know once I have any issue with all supporting messages. Thank you. Gaurav.

That is very good news. Looking forward to it. Kind regards Dagfinn [email protected]> wrote:

Hi Greg, I have installed 51.5. This version will be a part of MVS-TK5 Update-4. HI COBOL works fine. Cheers, Rob

What was complaining? z/OS? Hercules? Both? What was the message number and text of the complaint, or complaints? Have you referred to the message manual(s)?

Hi, I am using Hercules 4.8 Development branch on Ubuntu 20.04 LTS and Guest OS is z/OS 3.1. Following configuration works well, however OSA1500 interface gets disconnected in few hours complaining

Hi Rob, Then you should be able to make that 51.5 at that time. :) Review 51.5 includes enhancements to the previously undocumented HI COBOL. Cheers, Greg