Anyone that can help me figure out what is causing this message:?
IKT00405I SCREEN ERASURE CAUSED BY ERROR RECOVERY PROCEDURE
when trying to connect a terminal.?
No it is not connected as local terminal but connected via the IBM3705 emulator by Henk & Edwin which I have patched to handle BSC rather than SDLC. The BSC communication seems to be working since there are no NAKs seen in the logs and BSC TEXT messages are going in both directions as anticipated.
But I get this message what ever I try to do on the terminal.
Unfortuately my fluency in VTAM is not so good. This is the config file I have come up with. Basically adapted the one Henk & Edwin provided to handle BSC:
Comments? Hints?
*
* *
* THIS GENERATION IS FOR AN IBM 3705 *
* *
*
SPACE 2
*
* PCCU SPECIFICATIONS - OS/VS (VTAM ONLY) *
*
NCPSTART PCCU CUADDR=660, 3705 CONTROL UNIT ADDRESS X
AUTODMP=NO, PROMPT BEFORE DUMPING NCP X
AUTOIPL=YES, AUTOIPL AND RESTART X
DUMPDS=NCPDUMP, AUTODUMP REQUESTED X
INITEST=YES NCP INITIALIZATION TEST
EJECT
*
* BUILD MACRO SPECIFICATIONS FOR OS *
*
NCPBUILD BUILD MAXSUBA=31, MUST BE SAME AS IN VTAM STR DEF X
LOADLIB=NCPLOAD, LIBRARY FOR NCP LOAD MODULE X
OBJLIB=NCPOBJ1, LIBRARY FOR ASSEMBLER OUTPUTS X
LESIZE=320, REGION SIZE FOR LINK-EDIT X
TYPSYS=OS, OS USED FOR STAGE 2 X
QUALIFY=SYS1, 1ST LEVEL QUALIFIER X
UNIT=SYSDA, DATA SET FOR ASSEMBLY X
MEMSIZE=64, 3705 STORAGE SIZE IS 64K BYTES X
TYPGEN=NCP, NCP ONLY X
ABEND=YES, ABEND FACILITY INCLUDED X
ANS=YES, AUTOMATIC NETWORK SHUTDOWN X
ASMXREF=NO, NO ASSEMBLER CROSS-REFERENCE X
BFRS=64, NCP BUFFER SIZE X
CHANTYP=TYPE2, PRIMARY CHANNEL ADAPTER X
ERASE=NO, DO NOT ERASE BUFFERS (DEFAULT) X
ENABLTO=2.2, LEASED LINE ONLY (DEFAULT) X
JOBCARD=MULTI, JOBCARDS PROVIDED BY NCP GEN X
MODEL=3705-2, . X
NEWNAME=HJS3705, NAME OF THIS NCP LOAD MODULE X
OLT=YES, ONLINE TEST AVAILABLE(DEFAULT) X
SLODOWN=12, SLOWDOWN WHEN 12% OF BUFFERS AVAIL X
SUBAREA=16, SUBAREA ADDRESS = 3 X
TRACE=(YES,10) 10 ADDRESS-TRACE ENTRIES
SPACE 2
*
* SYSCNTRL OPTIONS FOR VTAM OR TCAM *
* NOTE THAT OPERATOR CONTROLS ARE NOT INCLUDED. *
*
NCPSYSC SYSCNTRL OPTIONS=(MODE, X
RCNTRL,RCOND,RECMD,RIMM,ENDCALL, X
BHSASSC)
SPACE 2
*
* HOST MACRO SPECIFICATIONS OS VTAM *
* UNITSZ TIMES MAXBFRU MINUS BFRPAD EQUALS MAX MESSAGE SIZE *
* FOR INBOUND MESSAGES *
*
NCPHOST HOST INBFRS=5, INITIAL 3705 ALLOCATION X
MAXBFRU=4, VTAM BUFFER UNIT ALLOCATION X
UNITSZ=4016, * X
BFRPAD=28, VTAM(OS=28, DOS=15, ACF=0), EXTM=2 X
DELAY=.2, .2 SECOND ATTENTION DELAY X
STATMOD=YES, YES VTAM, NO FOR EXTM X
TIMEOUT=(120.0) AUTO SHUTDOWN IF NO RESP IN 120SEC
SPACE 2
*
* CSB MACRO SPECIFICATIONS *
*
NCPCSB CSB SPEED=(1200), BUS MACH CLOCK X
MOD=0, SCANNER ADDRESS 020 TO 05F X
TYPE=TYPE2 TYPE 2 COMM SCANNER
EJECT
*
* SPECIFICATIONS FOR BSC LEASED LINES *
* GROUP MACRO SPECIFICATIONS *
*
BSC3270 GROUP LNCTL=BSC, SYNCHRONOUS DATA LINK X
DIAL=NO, REQUIRED FOR LEASED LINE X
TYPE=NCP, NCP ONLY X
TRANSFR=5, LIMIT NUMBER OF RECEIVE BUFFERS X
CUTOFF=1, LIMIT NUMBER OF SUBBLOCKS X
CRETRY=7, TIME OUT WILL TAKE 63 SECONDS X
XMITLIM=1, TRANSMISSION LIMIT X
REPLYTO=3 REPLY TIMEOUT
SPACE 2
*
* LINE MACRO SPECIFICATION - FULL-DUPLEX, LEASED *
* MAY BE USED FOR 3790, 3600, OR 3650 *
* *
* NOTE: LINE SPEED MAY BE RAISED TO 2400 FOR *
* ALL PHYSICAL UNITS AND TO 4800 FOR 3600 AND 3650 *
* WITHOUT DOING A NEW GEN OF NCP. *
* RETRIES VALUE FOR LINE SHOULD BE GREATER THAN 30 *
* SECONDS AND LESS THAN ONE MINUTE FOR 3650. *
* *
*
BSC01 LINE ADDRESS=020, TRANSMIT AND RECEIVE ADDRESSES X
DUPLEX=HALF, MODEM IS STRAPPED FOR HALF DUPLEX X
SPEED=9600, SPEED MAY BE HIGHER (SEE NOTES) X
NEWSYNC=NO, CHECK MODEM REQUIREMENTS X
CLOCKNG=EXT, MODEM PROVIDES CLOCKING X
NEGPOLP=.1, NEGATIVE POLL PAUSE X
POLLED=YES, POLLED DEVICE X
RETRIES=(5,10,4), 5 RETRIES PER RECOVERY SEQUENCE X
ISTATUS=ACTIVE, ACF/VTAM USE ONLY X
CODE=EBCDIC, EBCDIC 3270'S ONLY X
INTPRI=1, INTERRUPT PRIORITY IS 1 X
POLIMIT=(1,QUEUE), X
PAUSE=1, DELAY BETWEEN SERVICE CYCLES X
SERVPRI=OLD, PRIORITY TO OLD SESSIONS X
SESSION=1, SPECIFY 1 FOR EACH CLUSTER X
PU=YES, ACF/VTAM ONLY X
SSCPFM=USS3270
*
SPACE 2
*
* SERVICE ORDER FOR BSC LINK *
*
SERVICE ORDER=(BSC3274,BSCTERM1)
EJECT
*
* CLUSTER SPECIFICATIONS *
*
BSC3274 CLUSTER CUTYPE=3271, X
FEATUR2=(MODEL2,ANKEY,PFK), X
GPOLL=40407F7F, X
MODETAB=BSPLMT02
SPACE 2
*
* TERMINAL SPECIFICATIONS *
*
BSCTERM1 TERMINAL TERM=3277, X
FEATUR2=(MODEL2,ANKEY,PFK), X
ISTATUS=INACTIVE, X
ADDR=60604040, X
POLL=40404040
EJECT
*
* GENEND DELIMITER *
*
GENEND
END
